User manual BOSE VIRTUALLY INVISIBLE 791

[. . . ] VIRTUALLY INVISIBLE 791 SPEAKERS ® Installation Guide Installationsvejledning Installationsanleitung Guía de instalación Asennusopas Notice d'installation Telepítési útmutató Guida di installazione Gebruikershandleiding Podrcznik instalacji Installationsanvisning TAB 8 TAB 7 TAB 6 TAB 5 TAB 4 TAB 3 TAB 2 English SAFETY INFORMATION Important words of caution Please read this owner's guide completely before you start. Then carefully consider your experience using the tools and taking the precautions referred to here. If you have doubts about doing this installation, you should contact either the dealer you purchased the product from, an electrician, or a professional audio/video installer. You can describe the job and request a cost estimate before committing to installation service. [. . . ] Choose the proper spade bit to drill a hole that is large enough for the blade of your cutting tool. WARNING: Use eye protection and be sure to observe all safety precautions while using a drill or cutting tool. 2. Choose a spot near the center or closer to the outside edge of the circle, depending on which will be easier when you begin to use your saw. Cutting the speaker hole Be sure to cut carefully to make the hole as regular as possible. However, when the speaker is in place, the frame overlaps the cutting edge by 5/8 in. Hold the cutting blade in a vertical position and keep it straight as you cut the hole. This helps prevent the blade from angling away from the outlined circle. Using the template 1. Center the template on the spot where you want the center of the speaker grille. Press the template to the ceiling with your hand or use painter's tape to hold it in place. CAUTION: DO NOT trace around or cut around the tabs that are for use only when the template serves as a paint shield. 8 5/8 " (21. 9 cm) 6 English TAB 2 TAB 3 TAB 4 TAB 5 TAB 6 TAB 7 TAB 8 INSTALLATION 2. Insert the tip of your saw into the pilot hole and cut most of the way around the circular outline. Connecting the speaker As you connect the wires, be careful to match the polarity of each wire to the proper terminal, as described below. · If the screw does not seat properly, use the next highest torque setting to finish securing the screw. Tighten one of the four clamp screws until you can feel the frame press firmly against the ceiling. This indicates that the clamp is extended and is gripping the ceiling. Securing the speaker As you lift the speaker, keep the speaker cable above and out of the way to prevent pinching it. You may notice a security brace, located on the upper edge of the speaker, for use where local building codes require it. Use two hands to hold the edge of the speaker as you guide it into the ceiling hole. CAUTION: Be sure not to press on the two small drivers seated on the face of the speaker. Security brace Arrow One of four clamp screws Clamp CAUTION: Be careful not to damage or remove any of the foam gasket material along the edge of the speaker. Use the small arrow on the inside flange of each speaker to properly orient the speaker for your installation. Refer to "Placement guidelines" on page 4 to review guidelines for orienting the speakers relative to one another. CAUTION: Tighten these screws firmly, but avoid using so much pressure that the clamps compress the ceiling material. This can cause the material to crumble, creating an uneven surface with gaps between the speaker face and the ceiling. 8 English TAB 2 TAB 3 TAB 4 TAB 5 TAB 6 TAB 7 TAB 8 INSTALLATION 4. Locate the clamp screw opposite the one that is tightened and repeat the process with this clamp. These two tightened clamps will hold the speaker in place temporarily. Repeat the process with the other two clamps to firmly secure the speaker to the ceiling. Attaching the grille The grille is designed to fit into the slots on the rim of the speaker and lock into place with a slight clockwise twist. [. . . ] Or, to call Bose directly, refer to the address list included in the carton. ® 10 English TAB 2 TAB 3 TAB 4 TAB 5 TAB 6 TAB 7 TAB 8 REFERENCE Troubleshooting Problem The speakers do not play Possible solution · Check the settings on your receiver/amplifier. Refer to the owner's guide that came with it for instruction on settings. · If other stereo speakers are connected to a second set of audio outputs on your amplifier/ receiver, make sure to select the proper A or B speaker setting to match the A or B outputs connected to your Virtually Invisible® 791 speakers. · Check the balance control on your receiver/amplifier and make sure it is centered. [. . . ]