User manual BOSE CINEMATE SERIES I

[. . . ] CINEMATE TM DIGITAL HOME THEATER SPEAKER SYSTEM Français Español English SAFETY INFORMATION Please read this guide Please take the time to follow the instructions in this guide carefully. It will help you set up and operate your system properly and enjoy all of its advanced features. The Interface module is to be used only with the Acoustimass® module in the Bose® CineMateTM speaker system. WARNING: To reduce the risk of fire or electrical shock, do not expose the product to rain or moisture. [. . . ] Turn off the TV speakers (see "Turning off the TV internal speakers"). If you do not have the option of selecting either Fixed or Variable, turn off the TV speakers (see "Turning off the TV internal speakers"), exit the audio menu, and adjust the TV volume to about 80% of the highest volume. 13 Français SYSTEM SETUP Español English Installing or replacing the remote batteries SYSTEM SETUP 1. Insert two new AA (IEC-R6) 1. 5V batteries, or their equivalent, as shown in Figure 15. (Two AA batteries are supplied in the product carton. ) Match the plus (+) and minus (­) marked on the batteries with the plus (+) and minus (­) inside the battery compartment. Note: Replace the batteries when the remote control stops operating or its range seems reduced. Figure 15 Installing the remote control batteries (2) AA batteries (IEC-R6) + + Battery compartment cover Setting up the remote to control other sources The universal remote control provided with your CineMateTM speaker system can be programmed to control your TV, cable/satellite box, VCR, DVD player, and Digital Video Recorder (DVR) such as TiVo brands or ReplayTV brands. With the CineMate universal remote, you can enjoy the convenience of using only one remote control for all your home theater equipment. Finding device codes In order to control your TV and other sources with the universal remote control, you must program the remote with a five-digit device code for each source. To find device codes for your source, see the CineMate Universal Remote Device Codes book included in the product carton. Note: More than one code may work with your particular brand of device. If you notice a lack of response or limited functionality after setting up the remote, try a different code. To control your TV The steps below show how to set up the remote to control your TV. To set up the remote to control other sources, you will need to follow the same procedure, using the appropriate device code and source button for each source. Locate the TV section in the CineMate Universal Remote Device Codes book. Locate the five-digit device code(s) for your brand of TV and start with the first one. Press and hold Setup on the remote until all five source buttons light up. 14 English Español Français SYSTEM SETUP 4. On the remote keypad, enter the first device code for your brand of TV. Check that the TV source button blinks twice and turns off after the code is entered. Follow the same procedure for each of your other sources, using the appropriate device code and source button for each source. Note: During programming, the five source buttons will flash rapidly three times if you press an invalid key or enter an unavailable device code. If this happens, go back to Step 1 and start over. TV source button To control a combination device · If you are programming the remote to control a combination device that has more than one source, such as a VCR/DVD unit, you can program the combination code into either remote control source. You may find it convenient to program the code twice ­ once for the VCR and once for the DVD. · To find the right device code, first search the "COMBINATION" listings in the CineMateTM device codes book. If you cannot find a valid code there, then search the listings for individual device types (TV, CBL, VCR, DVD, etc. ). [. . . ] Bose also offers cable adapters, for use in running speaker cable through walls, and longer speaker wire, as needed. For further information or to order mounting brackets, stands, or cable adapters, contact your Bose dealer. Or, to call Bose directly, refer to the address sheet included in the carton. Troubleshooting Problem No power, no LEDs What to do · Make sure the Acoustimass® module power switch (230V units only) is turned on. · Make sure the power cord is inserted securely into the Acoustimass module and plugged firmly into an operating AC wall outlet (mains). [. . . ]