User manual BOSE ACOUSTIMASS 5 III
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual BOSE ACOUSTIMASS 5 III. We hope that this BOSE ACOUSTIMASS 5 III user guide will be useful to you.
You may also download the following manuals related to this product:
BOSE ACOUSTIMASS 5 III (144 ko)
BOSE ACOUSTIMASS 5 SERIES III (158 ko)
BOSE ACOUSTIMASS 5 SERIES III (140 ko)
BOSE ACOUSTIMASS 5 SERIES III (157 ko)
BOSE ACOUSTIMASS 5 SERIES III REV 05 (158 ko)
BOSE ACOUSTIMASS 5 SERIES III REV 05 (140 ko)
BOSE ACOUSTIMASS 5 SERIES III REV 05 (157 ko)
Manual abstract: user guide BOSE ACOUSTIMASS 5 III
Detailed instructions for use are in the User's Guide.
[. . . ] The Bose® Acoustimass® 5 Series III Speaker System
Owner's Guide October 22, 2001
AM196451_05_V. pdf
Introduction
Thank you
English
We appreciate your choice of the Bose® Acoustimass® 5 Series III speaker system. Your system features new third generation Acoustimass cube speaker arrays, a product of the continuous research and development at Bose Corporation. These cube speakers deliver more lifelike sound and better overall performance, yet are smaller than their predecessors.
Important information
Please read this owner's guide
The set-up and operation of your Acoustimass 5 Series III speaker system is significantly different from other speakers. It will help you set up and operate your system properly and enjoy all of its advanced features. [. . . ] Repack it in the original carton and notify Bose or your authorized Bose dealer immediately. · Remove the inner cartons containing the two cube speaker arrays. · Gently roll the carton over onto its side and then onto its opening. Note: While the wires provided are adequate for most installations, you may increase the distance between the cube arrays and the Acoustimass module by splicing in additional wire. If you do so, use similar gauge or thicker wire, and make sure you maintain the correct phase (+ to + and to ), and properly connect the wires.
3. Examining the cables and connections
Locate the four identical pairs of wires packed with the system. · Two wire pairs connect your cube arrays to the Acoustimass module. · The other two wire pairs connect the Acoustimass module to your receiver or amplifier. The marked wire (with a red, striped, or printed marker) connects to the positive (+) terminal at each connection. · The cube arrays and the Acoustimass module have red positive (+) connections.
AM196451_05_V. pdf
October 23, 2001
5
Setting Up
English
4. Connecting the cube arrays to the Acoustimass® module
Select one pair of wires, and locate the terminal tab on the rear of the left cube array. Just press the terminal tab on the back of the speaker to insert the marked wire into the red (+) terminal and the plain wire into the black () terminal (Figure 3). Repeat this process with the other pair of wires and the right cube array.
Figure 3
Connecting a cube array
Marked wire to red terminal
CAUTION: Do not connect your amplifier or receiver directly to the cube arrays. Cube arrays must be connected directly to the Acoustimass module or damage will result.
4. Next, locate the terminals marked OUTPUTS TO CUBE SPEAKERS on the rear of the Acoustimass module (Figure 4). Connect the other ends of the wires from the left cube array to the pair of terminals marked L. Make sure that the marked wire is connected to the positive (+) and the plain wire is connected to the negative () terminal. Now, repeat step 5 for the right cube array, connecting its wires to the terminals marked R.
Figure 4
Connecting cube arrays to the Acoustimass module
From left cube speaker From right cube speaker
To receiver or amplifier
6
October 23, 2001
AM196451_05_V. pdf
Setting Up
5. Connecting the Acoustimass® 5 Series III system to your receiver
1. Select one of the remaining two pairs of wires, and locate the left channel terminals on the Acoustimass module marked INPUTS FROM AMP OR RECEIVER. Depress the red, positive (+) tab, insert the marked wire and release the tab. Repeat the process for the black, negative () tab and the plain wire (Figure 5). [. . . ] Do not use any sprays near the system or allow liquids to spill into any openings. Also, do not use any solvents, chemicals, or cleaning solutions containing alcohol, ammonia, or abrasives. The grille assemblies on the cube arrays may be carefully vacuumed if necessary. Please note that the drivers are located directly behind the grille cloth, and are easily damaged if reasonable care is not taken.
English
Troubleshooting
Problem
One of the cube arrays does not play
What to do
· Turn off the receiver or amplifier. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE BOSE ACOUSTIMASS 5 III
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual BOSE ACOUSTIMASS 5 III will begin.