User manual BOSE 4.2 DIRECT REFLECTING

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. For 4. 2 DIRECT REFLECTING-27 or 4. 2 DIRECT REFLECTING-40 remotes in Europe only Bose Corporation hereby declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC and other applicable Directives. The complete Declaration of Conformity can be found at www. Bose. com/compliance. ii English TAB 2 TAB 3 TAB 4 TAB 5 TAB 6 TAB 7 TAB 8 INTRODUCTION Overview The 4. 2 DIRECT REFLECTING remote control is specifically designed to expand your Bose® LIFESTYLE® V25/V35 home entertainment system into another area of your home. Using the 4. 2 DIRECT REFLECTING remote control, you can listen to your main room system through a Bose link-enabled expansion product in another room. LIFESTYLE© V25/V35 system (main room) Unpacking Check the carton for the parts shown. 4. 2 DIRECT REFLECTING remote control Four Homewide AAA (IEC LR3) antenna batteries Save the carton and packing materials, which provide the safest way to transport this product. [. . . ] Contact your authorized Bose dealer immediately or call Bose Customer Service. Refer to the address list included with your LIFESTYLE® system for contact information. 4. 2 DIRECT REFLECTING remote control with expansion system 1 TAB 8 TAB 7 TAB 6 TAB 5 TAB 4 TAB 3 TAB 2 English EXPANDING YOUR LIFESTYLE® SYSTEM Connecting your homewide antenna Plug the antenna cable into the Homewide Antenna connector on your LIFESTYLE® system. Control console (main room) Connecting an expansion product to the control console 1. Plug one end of the Bose® link cable into the Bose link OUT connector on your LIFESTYLE® system control console. Control console (main room) Antenna cable Antenna (bare wire) Because the antenna radiates at 90 degrees to the antenna (bare wire), mount the antenna vertically as close as possible to the center of the house. Do not bundle the antenna together with other cables and do not place it close to large metallic objects or surfaces. 2. Connect the other end of the Bose link cable to your expansion product. Your expansion product might be a speaker system or an AL8 Homewide Wireless Audio Link if you are making a wireless connection. Refer to the owner's guide that came with your expansion product for more information on making this connection. 2 English TAB 2 TAB 3 TAB 4 TAB 5 TAB 6 TAB 7 TAB 8 EXPANDING YOUR LIFESTYLE® SYSTEM Getting the remote ready 1. Make sure your 4. 2 DIRECT REFLECTING remote and expansion product are set to the same room code. If the expansion product is also set to room B, you do not need to do anything. To change the remote control room code, see "Changing the room code" on page 8. To change the room code in the expansion product, see the owner's guide that came with it. Although the LIFESTYLE® system control console emits IR signals into the room where it is located, an IR emitter can better direct those signals to the TV. 7 TAB 8 TAB 7 TAB 6 TAB 5 TAB 4 TAB 3 TAB 2 English USING MULTI-ROOM AUDIO Room and house codes Room and house codes are the settings that allow you to operate your main room system from another room in your home that has a Bose® link-enabled expansion system. Each 4. 2 DIRECT REFLECTING remote and your main room system must have identical house codes. Also, each expansion system and the 4. 2 DIRECT REFLECTING remote used with it must have identical room codes. Locate the room code switches (6-9). Changing the room code Your 4. 2 DIRECT REFLECTING remote is set at the factory for room code B. If room code B is already used by another Bose link product in your home, you need to change both the 4. 2 DIRECT REFLECTING and expansion system to another room code. Press and slide the battery cover off the back of the remote. 8 English TAB 2 TAB 3 TAB 4 TAB 5 TAB 6 TAB 7 TAB 8 USING MULTI-ROOM AUDIO 3. Select a room code from the following table. Room Code B C D E F G H I J K L M N O 6 7 8 9 4. Using a fine-point pen or other small tool, set switches 6-9 to the corresponding up and down positions shown for that room code. Slide the battery cover back into place until it snaps closed. Changing the house code The radio frequency (RF) signals used in expansion systems have a long range and the ability to penetrate walls. Therefore, the signals from an 4. 2 DIRECT REFLECTING remote in one home can possibly reach and affect the operation of a LIFESTYLE® system in a nearby home. Changing the house code for the system and all the remotes used with it avoids possible conflict. [. . . ] Your 4. 2 DIRECT REFLECTING remote is set at the factory for house code 15. To change the house code in your 4. 2 DIRECT REFLECTING remote and in your LIFESTYLE® system: 1. Press and slide the battery cover off the back of the remote. 9 TAB 8 TAB 7 TAB 6 TAB 5 TAB 4 TAB 3 TAB 2 English USING MULTI-ROOM AUDIO 2. Select a house code from the following table. House Code 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 1 2 3 4 10 English TAB 2 TAB 3 TAB 4 TAB 5 TAB 6 TAB 7 TAB 8 USING MULTI-ROOM AUDIO 4. [. . . ]