User manual BOSE 151

[. . . ] Once you decide where you will use your 151 speakers, consider the optional allweather mounting and installation accessories from Bose. (Refer to "Accessories" on page 8. ) AM171297_09_V. pdf July 15, 2003 3 Decide where you want the speakers For best results, mount both speakers on the same wall, facing the listening area. (Outdoors, if you are not using an existing wall, consider the length of your listening area as your "wall. ") Measure the length of the wall and divide that length by six. Place the other speaker one-sixth the length from the right end (see Figure 1). If you place your 151® speakers outdoors, you will probably connect them to an amplifier or receiver that is inside. [. . . ] Note: Be sure to cut enough cord to reach from the receiver to each speaker. Unpack the speakers Unpack each speaker carefully. Repack both speakers in the original carton and notify your authorized Bose dealer immediately. AM171297_09_V. pdf July 15, 2003 5 Use the cord properly Speaker cord consists of two insulated wires. These correspond to the red (+) and black (­) terminals on the back of the speaker, receiver, or amplifier. Be sure to connect each wire to the proper terminal (positive to positive, negative to negative). · Prepare the ends of each cord At the ends of each cord, strip approximately 1/2 inch (12 mm) of insulation from both wires. · Connect the cords to your speakers At the back of your speaker, unscrew the hex knob on one terminal post. Now insert the second wire into the second terminal post (see Figure 2). · Protect the cord To guard against weather wear on exposed wires, see "How to maintain Bose® 151® speakers" on page 8. Make the connections 1. Connect the first cord to the left channel of your receiver or amplifier. Connect the second cord to the right channel and right speaker, following the same procedure. ® Figure 2 Insert the bare wire end into the opening on the terminal post. 6 AM171297_09_V. pdf July 15, 2003 ® ® Receiver or Amplifier Figure 3 Check the connections Check the speaker and receiver or amplifier connections carefully. This could create short circuits that can damage an amplifier or receiver. Tighten any loose connections before you plug in the receiver or amplifier. Test the connections To make sure your speakers operate correctly: 1. Place the speakers less than 6 inches (15 cm) apart, facing each other. 3. The sound should seem to come from a point between the two speakers. Then repeat steps 1 ­ 3. AM171297_09_V. pdf July 15, 2003 7 Accessories Bose Model SM-1 outdoor surface-mount brackets give sturdy support to 151® speakers attached to a shelf, wall, ceiling, roof overhang, or boat. You can mount the brackets horizontally or vertically, and change the angle to direct the sound. Bose FM-1 outdoor flush-mount brackets securely anchor 151 speakers to the bulkhead of a boat. These brackets install through the bulkhead surface, so only the speaker face and bracket trim are exposed. To order these brackets, or for more information about them, contact your authorized Bose retailer, or to contact Bose directly, see "Bose Corporation" on page 63. How to maintain Bose 151 speakers ® Protect the connections The bare wire ends of the speaker cord can be affected by exposure to the elements. You may use a silicone caulking material, such as RTV adhesive, to protect the connections. [. . . ] Connect it to the other outputs on the amplifier or receiver. ® · If the speaker plays, the problem is in the original cord that was connected to that speaker. · If the speaker does not play, the problem is in that channel of the receiver. If the above solutions fail to solve your problem, contact your authorized Bose® dealer to arrange for service, or to contact Bose directly, see "Bose Corporation" on page 63. Bose Corporation will make every effort to resolve the problem, within the terms of your warranty . Warranty period Bose 151 environmental speakers are covered by a limited five-year transferable warranty. [. . . ]