User manual BOSCH SMS53A12GB

[. . . ]     K 5HVHW  VHF % K PLQ $ K 6WDUW & 5HVHW VHF                    en Table of contents Intensive zone . 17 17 17 17 17 17 18 18 18 18 18 19 19 19 19 20 20 20 20 21 21 22 22 22 22 23 23 24 25 25 25 25 26 26 26 26 27 27 27 27 28 28 28 Safety instructions . 17 en Safety instructions Before you switch ON the appliance Please read the operating and installation instructions carefully. They contain important information on how to install, use and maintain the appliance. [. . . ] The expected programme duration flashes on the digital display )". Programme TurboSpeed 20 min. : When the START button P is pressed the first time, the heating up phase (approx. 25 min. , irrespective of the initial situation) of the appliance starts. After the appliance has been opened, loaded and closed, the rinsing phase (20 min. ) starts when the START button P is pressed the second time. Ï Intensive zone * vsIniezot ne Perfect for a mixed load. You can wash very soiled pots and pans in the lower basket together with normally soiled utensils in the upper basket. The spray pressure in the lower basket is intensified, the rinsing temperature is increased slightly. ¿ Extra drying * nxEtradigy An increased temperature during the final rinse and an extended drying phase ensure that even plastic parts dry better. There is a slight increase in the energy consumption. 17 en Remaining running time display When the programme is selected, the remaining running time of the programme is indicated on the digital display )". The running time is determined during the programme by the water temperature, the number of utensils as well as the degree of soiling and may vary (depending on the selected programme). Programme TurboSpeed 20 min. : During the heating up phase and the remaining running time are indicated alternately on the digital display; at the end p flashes, indicating that the appliance can be opened and loaded. When the appliance has been restarted, the remaining running time is indicated again during the rinsing phase. nargoTiep m theprgomyarthnfeonlhSwticigoutm a aefd Switching off automatically after the end of the programme * * depending on model To save energy, the dishwasher is switched off 1 minute after the programme ends (factory setting). Appliance does not switch off automatically : Off after 1 min : Off after 120 min – Close the door. – Hold down programme button # and press START button P until : . . . The LED for button # flashes and the digital display )" displays the factory setting : . – Press programme button # until the factory set value : is indicated on the digital display )". Each time the button is pressed, the set value increases by one level; when the value of : has been reached, the display jumps back to : (off). : Timer programming * * depending on model You can delay the start of the programme in 1-hour steps up to 24 hours. – Press button @ + until the digital display )" jumps to : . – Press @ + or – button until the displayed time corresponds with your requirements. – To delete timer programming, press the @ + or – button until )" : is indicated on the digital display. You can change your programme selection at any time until the programme starts. Switching off the appliance Short time after the end of the programme: – Switch off ON/OFF switch (. – Remove the utensils when they have cooled down. End of programme The programme has ended when the value : is indicated on the numerical display )". The following applies to TurboSpeed 20 min. : As soon as : is indicated on the digital display )", the rinse cycle has ended. [. . . ] The hot water setting : allows you to adjust your appliance optimally to operation with hot water. It is recommended to have a water temperature (temperature of the incoming water) of at least 40 °C and no more than 60 °C. It is not recommended to connect the appliance to hot water if the water is supplied from an electric boiler. – Hold down programme button # and press START button P until : . . . [. . . ]