User manual BOSCH PPS816M91E

[. . . ] 9 Produktinfo Additional information on products, accessories, replacement parts and services can be found at www. bosch-home. com and in the online shop www. bosch-eshop. com : Safety precautions Read these instructions carefully. You will only be able to use your appliance safely and effectively when you have read them. These operating and installation instructions should be retained, and passed onto the buyer if the appliance is sold. The manufacturer is exempt from all responsibility if the requirements of this manual are not complied with. [. . . ] For its use, the Simmer Cap needs to be placed on the auxiliary burner cap. Additional coffee maker support Only for use on the auxiliary burner with pans which are no more than 12 cm in diameter. Wok pan The wok pan diffuses intense heat uniformly, so that the food is cooked in less time and using less oil. Always follow the manufacturer's instructions when cooking with a wok pan. -------- Simmer Plate This accessory has been designed to reduce the level of heat at the lowest power setting. Place the accessory directly on the pan support with the cones facing upwards, never directly over the burner. Centre the pan over the accessory. Code HEZ298126 Additional wok pan support: cast iron (3. 3 kW) HEZ298127 Additional wok pan support: cast iron (4 kW) HEZ298110 Additional wok pan support: steel enamel (3. 34 kW) HEZ298114 Additional coffee maker support HEZ298105 Simmer Plate HEZ298128 Simmer Cap HEZ298103 Wok pan The manufacturer accepts no liability if these accessories are not used or are used incorrectly. Gas burners There are indications to show which burner each control knob operates. It is essential to ensure that all the burner parts and pan supports are correctly installed for the appliance to work correctly. Do not swap the burner caps around. 5 Power levels The progressive control knobs can be used to control the power needed, from minimum to maximum power. Setting High flame Low flame Û — ˜ Control knob off Maximum capacity or aperture and electricity on Minimum capacity or aperture Switching on manually 1. Press the chosen burner control knob and turn it Main switch/Hob lock (Main Switch) The hob may have a main switch to cut off the mains gas supply and switch off all the burners at the same time. This switch is very practical if there are children in the house or, if for any reason, all the burners must be switched off quickly. Use any type of lighter or flame (cigarette lighter, matches, etc. ) and bring it close to the burner. Switching on automatically If your hob can be switched on automatically (ignition sparkers): 1. Press the chosen burner control knob and turn it anticlockwise to the maximum power setting. While the control knob is still pressed down, sparks are produced on all burners. Turn the control knob to the required setting. If it does not come on, turn the control knob to the off setting and repeat the steps above. This time, press and hold the control knob for longer (up to 10 seconds). : Risk of deflagration! If after 15 seconds the flame does not ignite, switch off the burner and open a nearby window or door. Wait at least one minute before trying to switch the burner back on. To unlock the hob: 1. Press the main switch and turn it fully clockwise. Safety system Depending on the model, your hob may have a safety system (thermocouple) that prevents the flow of gas if the burners accidentally switch off. $ % The mains gas supply is turned on. You can now use your hob normally. Warnings WKHUPRFRXSOH LJQLWLRQ VSDUNHU To ensure that this device is active: 1. Without releasing the control knob, press and hold it down It is normal to hear a soft whistling noise while the burner is operating. This is caused by the presence of dust in the atmosphere, spilt liquids, etc. If the burner flames are accidentally blown out, switch off the burner operating control knob and do not try to relight it for at least 1 minute. A few seconds after the burner is switched off, a sound (thud) will be produced. This is not a fault - this means that the safety device is no longer operating. [. . . ] For the warranty to be valid, the appliance must not have been tampered with, or used inappropriately. The applicable warranty conditions are those set out by the company's representative office in the country of purchase. Proof of purchase must be presented to obtain the benefits of the warranty. We reserve the right to introduce changes. Used appliances and packaging If the ) symbol is shown on the specifications plate, bear in mind the following instructions: Environmentally-friendly waste management Unpack the appliance and dispose of the packaging by environmentally-friendly means. [. . . ]