User manual BOSCH PMF180E

[. . . ] F) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. 3) Personal safety a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. [. . . ] Technical Data Multi-function tool Article number Preselection of orbital stroke rate Rated power input Output power No-load speed n0 Oscillation angle, left/right Weight according to EPTA-Procedure 01/2003 Protection class PMF 180 E 3 603 A00 0. 0 / II WARNING The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be used to compare one tool with another. The vibration emission level will vary because of the ways in which a power tool can be used and may increase above the level given in this information sheet. This could lead to a significant underestimate of exposure when the tool is used regularly in such a way. Note: To be accurate, an estimation of the level of exposure to vibration experienced during a given period of work should also take into account the times when the tool is switched off and when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period. For lower voltage and models for specific countries, these values can vary. Declaration of Conformity We declare under our sole responsibility that this product is in conformity with the following standards or standardization documents: EN 60745 according to the provisions of the directives 89/336/EEC, 98/37/EC. Book Page 14 Monday, May 14, 2007 4:11 PM Assembly Changing the Tool Before any work on the machine itself, pull the mains plug. Selecting the Application Tool/Accessory Accessory BIM segment saw blade Material Wooden materials, plastic, non-ferrous metals Application Separating and plunge cuts; also for sawing close to edges, in corners and hard to reach areas; Example: shortening already installed bottom rails or door hinges, plunge cuts for adjusting floor panels Separating and deep plunge cuts; also for sawing close to edges, in corners and hard to reach areas; Example: Sawing off water pipes (PVC) or cable ducts flush against walls, floors or ceilings Sanding surfaces close to edges, in corners or hard to reach areas; Depending on the sanding sheet for, e. , sanding wood, paint, varnish, stone, glass When mounting the saw blade, wear protective gloves. HCS plunge cut saw blade, wood Wooden materials, plastic, gypsum and other soft materials Base plate for sanding, series Delta 93 mm Depends on sanding sheet HCS plunge cut saw blades, wood* Wooden materials, plastic, gypsum and other soft materials Smaller separating and plunge cuts; Example: Cut-outs in furniture for cable connections BIM plunge cut saw blades, metal* Metal (e. , nails, screws, small profiles), non-ferrous metals Smaller separating and plunge cuts; Example: Shortening narrow profiles, cutting fastening elements such as staples HM-Riff segment saw Grouting joints, soft wall blade* tiles, glass-fibre reinforces plastic and other abrasive materials Cutting and separating close to edges, in corners or hard to reach areas; Example: Removing grouting joints between wall tiles for repair work, cutting openings in tiles, gypsum boards or plastic * Optional accessory; for the complete accessories please see Bosch accessory programme. Book Page 15 Monday, May 14, 2007 4:11 PM Mounting/Replacing the Application Tool/ Accessory Mount the application tool/accessory (e. Plunge cut saw blade 7) in such a way on the tool holder 6 that the openings of the tool engage into the cams of the tool holder. For a safe and fatigue-free working position it is possible to position the application tools/accessories in any snap-in positions on the tool holder. Position the tool in such a way that the depressed centre points downwards (marking on the tool is readable from above, see figure on the graphics page). Incorrect or not securely fastened application tools/accessories can come loose during operation and pose a hazard. For removing the application tool/accessory loosen the screw 8 with the allen key 9 and remove the tool. Mounting/Replacing a Sanding Sheet on the Sanding Plate The sanding plate 10 is fitted with Velcro backing for quick and easy fastening of sanding sheets with Velcro adhesion. Before attaching the sanding sheet 11, free the Velcro backing of the sanding plate 10 from any debris by tapping against it in order to enable optimum adhesion. Position the sanding sheet 11 flush alongside one edge of the sanding plate 10, then lay the sanding sheet onto the sanding plate and press it against it with a light turning motion in clockwise direction. [. . . ] Book Page 54 Monday, May 14, 2007 4:11 PM Generelle advarselshenvisninger for el-værktøj ADVARSEL Læs alle advarselshenvisninger og instrukser. Undgå at bære el-værktøjet med fingeren på afbryderen og sørg for, at el-værktøjet ikke er tændt, når det sluttes til nettet, da dette øger risikoen for personskader. Nedan använt begrepp ”Elverktyg” hänför sig till nätdrivna elverktyg (med nätsladd) och till batteridrivna elverktyg (sladdlösa). Book Page 63 Monday, May 14, 2007 4:11 PM Illustrerade komponenter Numreringen av komponenterna hänvisar till illustration av elverktyget på grafiksida. [. . . ]