User manual BOSCH PDA180 PDA180E PDA240E

[. . . ] F) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. 3) Personal safety a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. [. . . ] For lower voltage and models for specific countries, these values can vary. noise/Vibration Information Measured values determined according to EN 60745. Typically the A-weighted noise levels of the product are: Sound pressure level 80 dB(A); Sound power level 91 dB(A). The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be used to compare one tool with another. The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over the total working period. Book Page 16 Thursday, December 13, 2007 2:21 PM 16 | English An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period. Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep the hands warm, organisation of work patterns. Certain dusts, such as oak or beech dust, are considered as carcinogenic, especially in connection with wood-treatment additives (chromate, wood preservative). Observe the relevant regulations in your country for the materials to be worked. External Dust Extraction (see figure A) Attach a vacuum hose 7 onto the outlet piece 3. An overview for connecting to various vacuum cleaners can be found at the beginning of these operating instructions. When vacuuming dry dust that is especially detrimental to health or carcinogenic, use a special vacuum cleaner. Declaration of Conformity We declare under our sole responsibility that the product described under “Technical Data” is in conformity with the following standards or standardization documents: EN 60745 according to the provisions of the directives 2004/108/EC, 98/37/EC (until Dec. Eckerhard Strötgen Head of Product Certification Replacing the Sanding Sheet (see figure B) 21. 2007, Robert Bosch GmbH, Power Tools Division D-70745 Leinfelden-Echterdingen When attaching a new sanding sheet, remove any dust or debris from the sanding plate 5 (e. To ensure optimum dust extraction, pay attention that the punched holes in the sanding sheet match with the holes in the sanding plate. The sanding plate 5 is fitted with Velcro backing for quick and easy fastening of sanding sheets with Velcro adhesion. Before attaching the sanding sheet 4, free the Velcro backing of the sanding plate 5 from any debris by tapping against it in order to enable optimum adhesion. Position the sanding sheet 4 flush alongside one edge of the sanding plate 5, then lay the sanding sheet onto the sanding plate and press it against it with a light turning motion in clockwise direction. [. . . ] Book Page 57 Thursday, December 13, 2007 2:21 PM Dansk | 57 Generelle advarselshenvisninger for el-værktøj da ADVARSEL Læs alle advarselshenvisninger og instrukser. Undgå at bære el-værktøjet med fingeren på afbryderen og sørg for, at el-værktøjet ikke er tændt, når det sluttes til nettet, da dette øger risikoen for personskader. Nedan använt begrepp ”Elverktyg” hänför sig till nätdrivna elverktyg (med nätsladd) och till batteridrivna elverktyg (sladdlösa). Book Page 69 Thursday, December 13, 2007 2:21 PM Norsk | 69 Generelle advarsler for elektroverktøy no ADVARSEL Les gjennom alle advarslene og anvisningene. [. . . ]