User manual BLUE SKY SUB 12 ACTIVE SUBWOOFER

[. . . ] SAT 6. 5 Active Satellite SUB 12 Active Subwoofer Owner's Manual for 2. 1 (stereo) Application blue sky SAT 6. 5 Active Satellite & SUB 12 Active Subwoofer Owners Manual for 2. 1 (stereo) Applications Issue 1 Contents Important 1 2 3 4 5 6 7 8 9 10 11 12 13 Safety Instructions _ __ __ __ __ __ __ __ __ __ _ Page 3 Philosophy and Introduction _ __ __ __ __ __ _ Page 4 What is THXpm3® Certification_ __ __ __ __ __ _ Page 4 Quick Setup _ __ __ __ __ __ __ __ __ __ __ __ _ Page 5 System Signal Connection Diagram _ __ __ __ _ Page 6 A Tour of Sat 6. 5 _ __ __ __ __ __ __ __ __ __ _ Page 7 A Tour of Sub 12 _ __ __ __ __ __ __ __ __ __ _ Page 8 Expanded Setup Guide _ __ __ __ __ __ __ __ _ Page 10 Cable and Wiring Specifications _ __ __ __ __ _ Page 11 Technical Information _ __ __ __ __ __ __ __ __ _ Page 12 Satellite Cabinet Dimensions _ __ __ __ __ __ _ Page 13 Subwoofer Cabinet Dimensions _ __ __ __ __ _ Page 14 Factory Service Instructions _ __ __ __ __ __ __ _ Page 15 Contact Details _ __ __ __ __ __ __ __ __ __ __ _ Page 15 Contents blue sky SAT 6. 5 Active Satellite & SUB 12 Active Subwoofer Owners Manual for 2. 1 (stereo) Applications Issue 1 Safety Instructions 1 READ INSTRUCTIONS - Read all safety and operating instructions before operating this product. 11. SERVICING - Do not attempt to service this product yourself. Opening or removing covers, including any over bottom or side speaker drivers, may expose you to dangerous voltage or other hazards. Refer all service to qualified service personnel. 2. RETAIN INSTRUCTIONS - Retain these safety and operating instructions for future reference. HEED WARNINGS - Follow all warnings on this product and in the operating instructions. [. . . ] It is important to remember that the positioning of the subwoofer in the room will impact the subwoofer level. You may find it necessary to increase or decrease the level from the reference position. If a more exacting setup is required, a pink noise generator, used in conjunction with a real time analyzer can be used to fully optimize the system (See Page 10 - Expanded Setup Guide). Just remember - Use your ears, they are the best audio tool you have and you will be amazed how accurate the setup can be if you use familiar audio material during the setup of the system. You have now completed the set up of one of the world's finest monitoring systems. If you have any questions, please do not hesitate to contact us directly with your questions. Refer to the wiring table below for wiring custom cables and connectors. 1/4 X 20 INSERTS - Located on the bottom of the subwoofer cabinet are four 1/4 X 20 inserts for spiked or rubber feet. IEC POWER TERMINAL - Connect to 120 Volt AC / 60Hz power source, rated for 430 WATTS. Use the included IEC Power Cable. 2. RIGHT/LEFT OUT - This XLR output should be connected to the right/ left input of the active satellite speaker. These outputs are bass-managed and are therefore bandwidth limited to spectral content above 80Hz. Refer to the wiring table in bullet point 1 for wiring custom cables and connectors. 3. SUB IN - This XLR input should be connected to either the subwoofer output of an external bass-management controller or the daisy-chain output (SUB OUT) of another Blue Sky Active Subwoofer. This input is fullbandwidth (up to approximately 200Hz) and does not use a low pass filter. Refer to the wiring table in bullet point 1 for wiring custom cables and connectors. 4. SUB OUT - A Subwoofer output for connecting additional subwoofers. This should be connected to the SUB IN of an additional Blue Sky SUB12. 5. MUTE - This switch is used to activate the automatic mute circuit built into the subwoofer. When the automatic mute circuit is activated, the system will automatically mute both the subwoofer and satellite outputs when no signal is present for 15 minutes. Once signal is present again, the system will automatically turn on. 6. PHASE - This switch is used to change the phase response of the subwoofer only. When this switch is in the 0 position, it is in-phase with the signal going to the Active Satellites. When this switch is in the position marked 180, it is 180 degrees out-of-phase with the signal going to the Active Satellites. Please refer to the Expanded Setup Guide (page 10) for instructions on how to use this switch. SUB GAIN & Power LED - This knob controls the input sensitivity of the subwoofer amplifier only. When set to the reference position, a 100mv signal at the input equals 90dB of output at one meter. [. . . ] In order to continually improve all of its products Blue Sky reserves the right to change these specifications without notice. SAT 6. 5 - 6 1/2" Active Satellite General Specifications Input Impedance SUB 12 - 12" Active Subwoofer General Specifications All subwoofer measurements are measured using the subwoofer direct input, which does not have a low pass filter. Voltage Sensitivity 90dB SPL @ 100mv @ 1M (40 to 80Hz bandwidth limited pink noise) Frequency Response (anechoic) 30 to 200Hz +/-3dB Typical In-Room Response 20 to 200Hz (3000 Cubic Feet) Bass Management Section Input Impedance 20k Ohms balanced Common Mode Rejection Ratio 40dB typical @60Hz Maximum Input Level (all inputs) +24dBu balanced Maximum Output Level Output Impedance Auto Mute Time Out Mute Threshold (all inputs) Left &Right Inputs to Sat Outputs Gain (balanced in and out) High-Pass Filter type High-Pass Filter Cutoff High-pass Filter Q THD + Noise Left & Right Inputs to Sub Out Gain Low-Pass Filter Type Low-Pass Cutoff +24dBu balanced 200 Ohms balanced >15 Minutes 30mV 0dB 2nd order Linkwitz-Riley 80Hz . 707 . 002% @ 1kHz @ +4dBu 0dB 4th order Linkwitz-Riley 80Hz 40k Ohms balanced Common Mode Rejection Ratio 40dB typical 60Hz Voltage Sensitivity 200mV = 90dB SPL @ 1M Maximum Input Level +24dBu balanced Frequency Response Low Frequency Cutoff Low Frequency Rolloff System Q System Crossover Frequency System Crossover Slope Enclosure * +/- 1. 5dB 200 to 10kHz +/- 3. 0dB 80 to 20kHz 80Hz 12dB per octave . 707 1. 5kHz 4th order Linkwitz-Riley Acoustic Solid 3/4" MDF construction with 1" front and rear baffle * Viscoelastic energy absorbing front baffle coating * 1/4"x 20 inserts for attachment of OmniMount( type 100 brackets. * Dimensions are 12" H x 8" W x 10 1/4" D (11. 88" with heatsink and tweeter wave guide) * Weight 27lbs. [. . . ]