User manual BLITZ BZLE4U7 QUICK START

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual BLITZ BZLE4U7. We hope that this BLITZ BZLE4U7 user guide will be useful to you.


BLITZ BZLE4U7 QUICK START: Download the complete user guide (164 Ko)

Manual abstract: user guide BLITZ BZLE4U7QUICK START

Detailed instructions for use are in the User's Guide.

[. . . ] A lower signal level will require increased sensitivity for full power. A higher signal level will require decreased sensitivity. 7. LINE INPUT RCA JACKS These inputs are for signal cables from the source. Always use high quality shielded RCA cables. 8. LINE OUT RCA JACKS The LINE OUT allows you to build multiple amplifier systems without having to use splitter cords to distribute the signal. [. . . ] Now it is simple a matter of bringing one set of RCAs into the first amplifier, then using the line out RCA jacks as the feed to the next amplifier. 9. BRIDGED MODE 4 Features & Controls Features & Controls 10. B-TERMINAL (CHASSIS GROUND) To avoid unwanted ignition noise caused by ground loops, it is essential that the Amplifier be grounded to a clean, bare, metal surface of the vehicles chassis. 11. REMOTE POWER ON To remote wire car stereo. This amplifier is turned "ON" remotely when vehicle's stereo is turned "ON". Note: IF YOUR RADIO DOES NOT HAVE +12 VOLT OUTPUT LEAD WHEN TURNED ON, THE "REMOTE" TERMINAL ON THE AMPLIFIER CAN BE CONNECTED TO VEHICLES ACCESSORY CIRCUIT WHICH PROVIDES +12V WHEN THE CAR IS ON. 12. B+ TERMINAL (BATTERY POSITIVE) Due to the power requirements of the Amplifier, this connection should be made directly to the positive(+) terminal of battery. For safety measure, install an in-line fuse Holder (not included) as close to the battery positive(+) terminal as possible with an ampere rating not to exceed total value of fuses in Amp. 13. REMOTE CONTROL INPUT LEVEL MIN MAX MIN REMOTE LEV EL MA X Remote Bass Boost Control Remote Bass Boost Control : This control adjusts the Bass Boost gain for the amplifier's speaker output (0 - +18dB) 5 Installation & Precautions Installation 1. Make sure there is sufficient air flow around the intended mounting location. Connect the power ground terminal to the nearest point on the chassis of the car. Connect the remote terminal to the remote output of the head unit using 14 gauge wire. Before making or breaking power connections in your system, disconnect the vehicle battery. Confirm that your head unit or other equipment is turned off while connecting the input jacks and speaker terminals. If you need to replace the power fuse, only replace it with a fuse identical to that supplied with the system. Using a fuse fo a different type or rating may result in damage to your system which isn't covered by the manufacturer's warranty. 6 System Wiring Wiring Diagram BZA-1000D / BZA-2000D BRIDGED MODE SLAVE MASTER LINE INPUT LINE OUT L DATA LINK PWR. PROT. BASS BOOST PHASE SHIFT LOW PASS SUB SONIC INPUT LEVEL R 0 +18 0 180 50 150 15 40 MIN MAX SPEAKER MONO BLOCK DIGITAL AMPLIFIER From OUTPUTS of To INPUTS of SATELLITE AMPLIFIER HEAD UNIT BZA-1000D SUB WOOFER 2 OHM BZA-2000D SUB WOOFER 1 OHM POWER GND +REM +12V FUSES REMOTE GROUND REMOTE TURN-ON Fuse Holder BZA-2000D ONLY Distribution Block LEVEL MIN MAX BATTERY REMOTE BASS LEVEL CONTROL Capasitor 7 System Wiring Bridging Two Amplifiers BZA-1000D / BZA-2000D BRIDGED SWITCH : MASTER POSITION SLAVE MASTER MASTER AMP BRIDGED MODE SLAVE MASTER LINE INPUT LINE OUT L DATA LINK PWR. PROT. BASS BOOST PHASE SHIFT LOW PASS SUB SONIC INPUT LEVEL R 0 +18 0 180 50 150 15 40 MIN MAX SPEAKER BZA-1000D SUB WOOFER 4 OHM BZA-2000D SUB WOOFER 2 OHM BRIDGED SWITCH : SLAVE POSITION SLAVE MASTER SLAVE AMP BRIDGED MODE SLAVE MASTER LINE INPUT LINE OUT L DATA LINK PWR. PROT. BASS BOOST PHASE SHIFT LOW PASS SUB SONIC INPUT LEVEL R 0 +18 0 180 50 150 15 40 MIN MAX SPEAKER 8 Troubleshooting Troubleshooting Amplifier will not power up. Check for good ground connection. [. . . ] PROT. BASS BOOST PHASE SHIFT LOW PASS SUB SONIC INPUT LEVEL R 0 +18 0 180 50 150 15 40 MIN MAX SPEAKER 8 Troubleshooting Troubleshooting Amplifier will not power up. Check for good ground connection. If it is lit, shut off amplifier briefly and then repower it. High hiss or engine noise (alternator whine) in speakers. Disconnect all RCA inputs to the amplifier(s)-if hiss/noise disappears, then plug in the component driving the amplifier and unplug it's inputs. If hiss/noise disappears, go on until the faulty/ noisy component is found. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE BLITZ BZLE4U7




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual BLITZ BZLE4U7 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.