User manual BLAUPUNKT TRAVELPILOT DX-R 70

[. . . ] TravelPilot Navigation Radio/CD TravelPilot DX-R70 Operating instructions http://www. blaupunkt. com INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP INDEX 2 Device overview 1 2 3 4 5 6 7 8 9 17 16 15 14 13 12 11 10 1 2 3 4 button ­ opens the control panel. Button to switch the unit on/off and operate the mute volume function. For further information, read the section entitled "Programming the macro button" in the "Setup" chapter. If pressed briefly during navigation: the active destination is displayed and the last voice output is repeated. [. . . ] To view the subsections, highlight the entries marked with a "+" and keep the OK button pressed for longer than two seconds. Sections that cannot be excluded (for instance, because there is no available alternative route) are marked with a lock symbol. 3 4 5 Press the OK button 8. / buttons on the rocker switch 7 to move the selection Use the marker to the last road that you want excluded from your route. The navigation session is displayed again and the route list is recalculated. NEW CALC appears in the title line whilst the route is being calculated. If you want to cancel an exclusion, select CLEAR; the navigation session is displayed again and the route is recalculated. If you want to change the exclusion, select MODIFY and repeat steps 3 - 6 listed in the "Excluding a route" section. 6 Cancelling / changing exclusions 1 2 INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP INDEX 49 DEUTSCH DEUTSCH The navi menu is displayed. DEUTSCH ENGLISH Use the / buttons on the rocker switch 7 to move the selection marker to the first road that you want excluded from your route. If necessary, open longer sections as already described. INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP INDEX 50 Defining route options You can customise the route to suit your requirements at any time, even during an active navigation session. The configurable parameters are: ROUTE: Choose between the quickest or shortest route or dynamic navigation with TMC. If you select DYN. , the options listed below will be hidden from view; the TravelPilot calculates the quickest route whilst taking into account the current traffic messages and automatically tunes into a TMC station. MOTORWAY: You can set whether you want to use motorways during your navigation session. FERRY: You can set the system to be able to use ferries or avoid them. TOLL: You have the option of excluding or including roads for which a toll charge is levied in your navigation sessions. Note: If, for instance, MOTORWAY AVOID is set, and a very long detour would be the result of applying this option, the TravelPilot will instead decide to include motorways in its route calculations. Select the menu item you want to change and press the OK button 8. NAVI. MENU MODIFY ROUTE TRAFFIC AHEAD ROUTE OPTION ROUTE LIST POSITION MARK ROUTE OPTION ROUTE FAST MOTORWAY WITH FERRY WITH TOLL WITH CONTINUE ROUTE OPTION ROUTE DYN. - CONTINUE If you want to close the selection menu, 1 2 select the CONTINUE menu item and press the OK button 8. If navigation is active, you will be switched to the navigation session. Note: If you change the route options whilst a navigation session is active, the route will be recalculated. The set route options remain active until they are changed again. Setting a position marker You can save your current vehicle position at any time, even during an active navigation session. This feature is useful if you notice an interesting location during your journey and want to return to it at some other point in time. To set a position marker for your current position, 1 2 3 press the MENU button :. For further information, read "Programming the macro button" in the "Setup" chapter. NAVI. [. . . ] FM-SEEK SENS KEYCARD Step 2: This query refers to deleting the name and playlist memory for CD mode. Step 3: The last step affects all the options, all the setup settings and all the sound settings of the audio sources. 4 4 If you want to delete the settings, press YES or to retain the settings, select NO. If you confirmed at least one item with YES, the device will be reset. Note: A table containing the factory default settings for the device is located at the end of this chapter. Setting seek tuning sensitivity You have the option of setting the seek tuning stop sensitivity for automatic seek tuning mode. buttons on the rocker switch 7 to select the FM-SEEK Keep pressing the OK button 8 until the required option is displayed inversed alongside FM-SEEK. [. . . ]