User manual BLAUPUNKT TRAVEL PILOT DX-N SIL. I

[. . . ] 2). ­ 1. 2 Power connection to vehiclespecific plugs If the radio connection in your vehicle was fitted with a 10A fuse at the factory (see operating instructions or the fuse box in your car. ), you will still need the vehicle-specific adapter cable (see Fig. 3). Observe the following safety information while installing and connecting the system: ­ ­ Disconnect the negative terminal of the battery. In doing so, observe the safety information provided by the vehicle manufacturer. [. . . ] The TravelPilot can be used in vehicles with: · 12 V battery power · Negative pole on the chassis 2. Connecting the speakers 2. 1 Connecting the speakers to the ISO standard plug In vehicles pre-equipped with passive speakers (with 4-ohm speakers) you can adapt the ISO plug in the vehicle. If necessary, the ISO cable (Order-No. 7 607 647 093) can be used for extra length (see Fig. Order special adapter cables from your dealer for vehicles pre-equipped with active speakers. 1. Power supply 1. 1 Connection to the vehicle ISO standard plug To prevent electrical malfunctions in vehicle ISO plugs, you have to use the universal ISO adapter cable (OrderNo. The following vehicles with ISO standard connections can currently be fitted with the universal ISO adapter cable: Alfa Romeo, Citroen, Fiat, Honda, Lancia, Mercedes, Peugeot, Porsche, Renault, Skoda. ­ ­ ­ ­ Installation instructions 3. Installing the antenna Connect the antenna wiring to the enclosed bracket(see Fig. Installing the TravelPilot 4. 1 Setting the Gyro Important: Before the TravelPilot is inserted, the gyroscope must be put in a horizontal position (see Fig. Note: Once the handles have locked into place, they cannot be removed until you pull the TravelPilot out of the compartment. 4 5. Connection diagrams Power connection to the vehicle ISO standard plug . . . . . . . . . Fig. 10 4. 5 Connecting the back-up light signal wire The back-up light signal wire connects the system to the vehicle back-up light. Make sure that this connection is charged with 12 volts when the vehicle is reversing. Important: We assume no liability for faulty connections and their consequences! 4. 6 Connecting the speedometer signal Important : Only an authorised customer service centre should make this connection. The speedometer signal wire connects the system to the vehicle-specific speedometer signal connection. Important : We assume no liability for faulty connections and their consequences! Installation instructions 7 607 621 126 A A F RR R R LF L Fig. 1 * Tel. -Mute (active low) Fig. 4 + + + + - 4 Ohm 4 Ohm 4 Ohm 4 Ohm 7 607 621 129 GPS antenna Bracket A * Fig. 2 1. Fig. 5 A GPS antenna Fig. 3 * 5 2. Radio antenna Installation instructions 6 Fig. 6 ­10 ° ° +30 Fig. 6a 90° 1 2 1 Fig. 7 ­10 ° +30 ° O. K. ­10° 2 90° +3 0° Fig. 8 Installation instructions C-1 1 4 3 2 5 6 C-2 7 10 9 12 8 11 C-3 13 16 19 15 18 14 17 20 A B 1 2 3 4 5 6 7 8 Speaker out RR+ Speaker out RRSpeaker out RF+ Speaker out RFSpeaker out LF+ Speaker out LFSpeaker out LR+ Speaker out LR1 2 3 4 5 6 7 8 9 10 D GND -- -- -- -- -- Sensor -- Sensor -- C B A C 9 10 D 5 6 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 Gala/Tacho Tel. -Mute (active low) RFLS Permanent +12V Aut. [. . . ] antenna Illumination Ignition Ground 7 1 3 2 4 8 Wheel sensor C3 13 14 15 16 17 18 19 20 CDC Data-IN CDC Data-OUT +12V Permanent +12V switch voltage (max. 300mA) CDC Data-GND CDC AF/AUX-GND CDC AF/AUX- L CDC AF/AUX- R C1 1 2 3 4 5 6 Line Out LR Line Out RR Line Out GND -- -- +12V switch voltage (max 150mA) 7 8 9 10 11 12 C2 -- -- -- +12V switched voltage (max. 150mA) Remote Control-In Remote Control-GND Fig. 9 Equalizer Amplifier RC 06 CD changer 7 Installation instructions Control cable (Power Antenna +) The control cable is the connected positive output for auxiliary components e. g. : power antennas, (maximum load < 150 mA). [. . . ]