User manual BLAUPUNKT TRAVEL PILOT DX-N NAV. GB

[. . . ] 3 Preparing for installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Installing the navigation unit (Fig. 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Mounting location for the navigation unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Positive connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Negative connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Attach the fuse holder to protect the positive cable a maximum of 30 cm from the vehicle battery and connect it to the positive terminal on the battery (if necessary, drill a hole through the splashboard and use cable grommets accordingly). Connect the positive switching cable (black) with the fuse holder at terminal 15 (+ switched via ignition) behind the fuse. In vehicles in which it is not possible to connect the cable in the fuse box, use the enclosed fuse holder to connect the cable directly to terminal 15 at the ignition. Notes on the operation of the equipment To ensure the trouble-free operation of the navigation system, a distance calibration must be performed after the equipment has been installed. The service software integrated into the basic navigation unit allows you to start up the navigation system and to calibrate the wheel sensor using the SERVICE MENU following the installation of the unit or during later servicing. All that is required is a straight stretch of road of at least 100 m in length. The software also provides additional service functions for analysing any malfunctions in the navigation system. The system determines the distance travelled via a connection to the vehicle's speedometer signal. If there is no speedometer signal available, it will be necessary to have a wheel sensor mounted by an authorised customer service agent. The wheel sensor scans a magnetic strip which is glued to the wheel rim and delivers information on the distance travelled by the wheel. Due to automatic length adaptation, the magnetic strip must be applied to the non-driven left-hand wheel. The system recognises driving forwards and backwards by evaluating the back-up signal (forwards = 0 volts, backwards = 12 volts) received via the connection contact (RFLS) provided for that purpose. -3- Negative connection Screw the negative cable (brown) directly onto the chassis. Before drilling the holes for the mounting screws, make sure that no damage will be done to covered wiring, the petrol tank or fuel lines! Installing the control unit Installing the display Safety instructions Never grease or oil the ball-and-socket joint. The monitor cable must be laid so that it is not subjected to any tensile strains or other loads. Do not mount the monitor within the inflation range of the airbags (on the driver's side, the passenger side or the side airbags) or where it might strike the head or knees of anyone in the vehicle in the event of an accident!Before drilling the holes for the mounting screws and wiring, make sure that no damage will be done to covered wiring, the petrol tank or fuel lines!Mount the control unit bracket in a location where the control unit will be easily accessible, e. g. Do not mount the control unit within the inflation range of the airbags (on the driver's side, the passenger side or the side airbags) or where it might strike the head or knees of anyone in the vehicle in the event of an accident!Before drilling the holes for the mounting screws, make sure that no damage will be done to covered wiring, the petrol tank or fuel lines!Make sure that the vehicle operating elements remain easily accessible and are not obstructed in any way (gear stick, hand brake, etc. )! Positive-negative connection Connect the negative cable (brown) directly with the negative cable of the navigation computer (same ground potential). Connect the positive cable (switched + 12 V) directly with the positive cable (switched + 12 V) of the navigation computer. Upon customer request, the lighting connection (orange) can be connected with vehicle terminal 58d. Please refer to the instructions provided by the vehicle manufacturer. Important instructions for connecting the speedometer signal Please observe the following notes when connecting the speedometer signal: 1. [. . . ] Sensor kit no. : 7 612 001 277. Installation tolerances for the wheel sensor Clearance Z: Z = 6. 5 ± 1 mm (steel rim) Z = 5 - 0/+ 1 mm (aluminium rim) with respect to the centre of the wheel sensor, (Fig. The centre of the sensor must be located over the magnetic strip for the entire circumference of the wheel, (Fig 13). The edges of the wheel sensor must be set at a distance conforming to Z, (Fig. The wheel sensor and the magnetic strip should be installed by an authorised customer service agent only. [. . . ]