User manual BLAUPUNKT TRAVEL PILOT DX-N BLACK I

[. . . ] - Depending on the model, your vehicle may differ from the description provided here. We accept no responsibility for any damages due to incorrect installation or connection or for any consequential damages. If the information provided here is not suitable for your specific installation requirements, please contact your Blaupunkt dealer, your vehicle manufacturer or our telephone hotline. ­ The TravelPilot can be used in vehicles with: · 10, 5-14, 4 V battery power · Negative ground chassis Information on proper functioning To ensure that the TravelPilot functions properly, it is essential that the system be calibrated after it has been completely installed (see Operating instructions / Contents / Calibration). [. . . ] The system determines the distance travelled via its connection to the vehicle speedometer signal. If there is no speedometer signal, it will be necessary to have a route sensor mounted by an authorised customer service center. In this case you will have to order a sensor kit (route sensor, magnet strip, bracket and plug) from your dealer. Installing the antenna Connect the antenna wiring to the enclosed bracket (see Fig. Installing the TravelPilot 2. 1 Setting the Gyro Important: Before the TravelPilot is inserted, the gyroscope must be put in a horizontal position (see Fig. Important: Installation position of the TravelPilot: right / left: min. +30° The TravelPilot is installed in the standard car radio compartment provided by the manufacturer (see Fig. Connection diagrams Power connection to the vehicle ISO standard plug . . . . . . . . . 10 2. 6 Connecting the speedometer signal Important: Only an authorised dealer should make this connection. The speedometer signal wire connects the system to the vehicle-specific speedometer signal connection. Important: We assume no liability for faulty connections and their consequences! RR R LR F LF + + + + - 4 Ohm 4 Ohm 4 Ohm 4 Ohm GPS antenna A Bracket Fig. 5 3. Radio antenna 305 DEUTSCH GPS antenna A ENGLISH DEUTSCH Fig. 7 ­10 ° ° +30 O. K. ­10° 2 90° 0° +3 Fig. 8 C-1 1 4 3 2 5 6 C-2 7 10 9 12 8 11 C-3 13 16 19 15 18 14 17 20 A B 1 2 3 4 5 6 7 8 Speaker out RR+ Speaker out RRSpeaker out RF+ Speaker out RFSpeaker out LF+ Speaker out LFSpeaker out LR+ Speaker out LR- D 1 2 3 4 5 6 7 8 9 10 GND -- -- -- -- -- Sensor -- Sensor -- C B A C D 5 6 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 For wheel sensor use only C3 13 14 15 16 17 18 19 20 CDC Data-IN CDC Data-OUT +12V Permanent +12V switch voltage* CDC Data-GND CDC AF/AUX-GND CDC AF/AUX- L CDC AF/AUX- R C1 1 2 3 4 5 6 Line Out LR Line Out RR Line Out GND Line Out LF Line Out RF +12V switch voltage* 7 8 9 10 11 12 C2 Telefon NF in + Telefon NF in ­ Mute active (low) +12V switched voltage* Remote Control-In Remote Control-GND * Sum. [. . . ] 8 C-1 1 4 3 2 5 6 C-2 7 10 9 12 8 11 C-3 13 16 19 15 18 14 17 20 A B 1 2 3 4 5 6 7 8 Speaker out RR+ Speaker out RRSpeaker out RF+ Speaker out RFSpeaker out LF+ Speaker out LFSpeaker out LR+ Speaker out LR- D 1 2 3 4 5 6 7 8 9 10 GND -- -- -- -- -- Sensor -- Sensor -- C B A C D 5 6 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 For wheel sensor use only C3 13 14 15 16 17 18 19 20 CDC Data-IN CDC Data-OUT +12V Permanent +12V switch voltage* CDC Data-GND CDC AF/AUX-GND CDC AF/AUX- L CDC AF/AUX- R C1 1 2 3 4 5 6 Line Out LR Line Out RR Line Out GND Line Out LF Line Out RF +12V switch voltage* 7 8 9 10 11 12 C2 Telefon NF in + Telefon NF in ­ Mute active (low) +12V switched voltage* Remote Control-In Remote Control-GND * Sum. 9 RC 10 CD-Changer 307 DEUTSCH ENGLISH DEUTSCH 1 2 3 4 5 6 7 8 Gala/Tacho Tel. -Mute (active low) RFLS Permanent +12V Aut. antenna Illumination Ignition Ground 1 3 2 4 ENGLISH 9 7 8 10 308 Control cable (Power Antenna +) The control cable is the connected positive output for auxiliary components e. g. : power antennas, (maximum load < 150 mA). [. . . ]