User manual BLAUPUNKT TRAVEL PILOT DX-N BL CH

[. . . ] In this case, you must purchase a sensor kit (odometer, magnetic strip, installation bracket and plug) from your dealer. Loudspeaker connection 2. 1 Loudspeaker connection to standard ISO plug The loudspeaker connection is made in chamber B (see Fig. If the vehicle is prefitted for a passive installation (with 4-ohm loudspeakers), you can convert the ISO plug that is present in the vehicle. If the vehicle is prefitted for an active installation, you can obtain special adapter cables from your dealer. 95 · 96 3. [. . . ] Antenna installation 3. 1 Radio antenna In the case of vehicles that have been prefitted (e. g. VW, Seat, Audi), the supply voltage for the antenna is provided via the antenna cable (see the vehicle's operating instructions). If you want to replace the original equipment radio with a standard radio, you must obtain an antenna supply diplexer (Order no. You will find details on installing and connecting the antenna in the antenna installation instructions. After carrying out the installation, plug the antenna cable into the socket designated for this on the TravelPilot (see Fig. 3). For this reason, the dashboard provides a suitable installation position directly behind the windscreen, as long as the windscreen has no metallic coating and the windscreen wipers do not block the view. The antenna should be installed in the middle of the dashboard at a distance of at least 2 cm from the windscreen. Note: Despite these recommendations, installing the GPS antenna inside the vehicle is still unfavourable. For this reason, no guarantee can be given that the system will function correctly. This might lead to navigation inaccuracy since the TravelPilot will not be able to detect whether the vehicle is reversing. We do not accept liability for incorrect connections and their consequences. 5. Sensor test After carrying out the installation, you should test the connected sensors using the sensor test (see operating instructions / Setup - Basic settings / Installation). 6. Connection diagrams Electrical connection to the vehicle-specific plugs . . . . . . . . . . . . . . . . . You must now insert the stirrups into the designated holes on the left and right of the surround panel and push them in until you hear a clear clicking sound (side springs unlocked). The connecting cables can now be disconnected by pressing on the sides of the clips on the respective plug-and-socket connections (see Fig. 5). 4. 5 Connecting the speedometer signal The connection is made using a cable from the vehicle-specific speedometer signal connection to pin 1 of chamber A (see Fig. This connection should be carried out by one of the vehicle manufacturer's authorized workshops. 97 98 GPS antenna A 7 607 621 . . . 3 Radio antenna A RR F LR RF L + + + + - 4 ohms 4 Ohm 4 Ohm ohms 4 Ohm ohms 4 Ohm ohms Fig. [. . . ] This connection should be carried out by one of the vehicle manufacturer's authorized workshops. 97 98 GPS antenna A 7 607 621 . . . 3 Radio antenna A RR F LR RF L + + + + - 4 ohms 4 Ohm 4 Ohm ohms 4 Ohm ohms 4 Ohm ohms Fig. 4a 90° 1. 10 ­ ° ° +30 O. K. ­10 ° 0° +3 2. 6 99 100 C-1 1 4 3 2 5 6 C-2 7 10 9 12 8 11 C-3 13 16 19 15 18 14 17 20 A B 1 2 3 4 5 6 7 8 Loudspeaker RR+ Loudspeaker RRLoudspeaker RF+ Loudspeaker RFLoudspeaker LF+ Loudspeaker LFLoudspeaker LR+ Loudspeaker LR1 2 3 4 5 6 7 8 9 10 -- -- -- -- -- D C B A C 9 10 D 5 6 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 Gala/speedometer Telephone mute (active low) Reversing light signal Continuous positive (terminal 30) Autom. [. . . ]