User manual BLAUPUNKT TRAVELPILOT 500

[. . . ] www. blaupunkt. com Mobile Navigation TravelPilot 500 Operating and installation instructions (Long version) Device overview Device overview 1 2 3 4 6 7 5 8 9 10 11 12 17 16 15 14 13 2 Device overview 1 Display (touchscreen): Simple and intuitive operation by touching the buttons on the display. 2 VOL -: Decreases the volume 3 On/Off switch: · Long press (for longer than 1 second): Switches the device on · Long press (for longer than 3 seconds): Switches the device off · Short press: Calls up the main menu 4 VOL +: Increases the volume 5 Socket for additional external TMC antenna (internal TMC antenna is present) 6 Memory card slot 7 Socket for power supply (battery charger or charger cable for the cigarette lighter) 8 Stylus for operation on the display 9 Digital camera, among other things for recognising signs : Light sensor for automatic display brightness (top side) ; Socket for additional external GPS antenna (internal GPS antenna is present) < Battery compartment cover = Microphone for speech input and hands-free system (Bluetooth) > Socket for headphones ?· Do not expose the device to very low (below -20 °C) and very high temperatures (above 60 °C), e. g. close to fire, heating devices or in a parked car with direct exposure to the sun. [. . . ] The function uses additional current, thereby reducing the operating time of the navigation device. Touch the symbol to activate (check u mark) or deactivate (no check mark) Bluetooth. Registering additional cell phones with the navigation device Start the search for Bluetooth-ready devices if you want to register additional cell phones. If a Bluetooth connection currently exists, no additional cell phone can be registered. It must be disconnected since the connection can be established only to one device. · The Bluetooth connection can be established only to one cell phone. If additional ones are available, only the cell phone registered last is connected. u Proceed as described in the chapter "Registering with the navigation device" and enter the PIN "0000". 42 Bluetooth function Switching visibility on/off For the Bluetooth connection, the navigation device must be visible to other Bluetooth-ready devices. Touch the symbol to switch the visiu bility on (check mark) or off (no check mark). Paired devices All registered cell phones are listed in the Paired Devices menu and can be edited. Prerequisite: · Bluetooth function and visibility in the cell phone are activated Note: The Bluetooth connection can be established only to one cell phone. If additional ones are available, only the cell phone registered last is connected. Touch the symbol to delete all cell phones. Ringtone u Touch the symbol. u Press the VOL - or VOL + button to adjust the volume. Establishing the connection automatically If you switch off the device, the Bluetooth connection is disconnected. The automatic connection causes the devices to be reconnected as soon as the device is switched on again. On the second page of the Bluetooth u Settings menu, touch the symbol to allow the automatic connection (check mark) or to prevent it (no check mark). Changing the PIN If you want to connect devices with each other via Bluetooth, you are requested to enter a PIN. To use your cell phone as a modem, configure the access in the navigation device. Note: Note that the cell phone for an Internet connection must be connected using the "DUN" Bluetooth profile (Dialup Networking Profile) (ch. "Registering with the navigation device"). u u u u u u u u 43 Bluetooth function | Illustrated phrase book | Camera function Obtain the following settings from your service provider or the operating instructions of your cell phone: · APN: e. g. "tm" · DHCP (optional) · DNS 1/2 (optional) · Dial: Phone number · Login script (optional) Prerequisite: · Cell phone with modem function · Bluetooth connection Touch the symbol on the second page u of the Bluetooth Settings menu. Automatic call answering The automatic call answering causes incoming calls to be answered automatically. On the second page of the Bluetooth u Settings menu, touch the symbol to switch the function on (check mark) or off (no check mark). u Touch the Language button if you want to change the initial or target language. [. . . ] "Working with the map", "Map/navigation settings") · How to activate and deactivate POI notes to be notified about your POIs in time (ch. "Working with the map", "Map/navigation settings") · How to load your planned tours from a memory card (ch. "Tour planning") · How to select your planned tour from the memory (ch. "Using a destination/tour from the destination/tour memory") 17 Country: Germany Austria Denmark Finland Great Britain Greece Ireland Italy Luxembourg Norway Portugal Spain Sweden Switzerland Czech. [. . . ]