User manual BLAUPUNKT TRAVELPILOT RNS4

[. . . ] TravelPilot Navigation Radio/CD TravelPilot DX-R4 / RNS4 Operating instructions http://www. blaupunkt. com INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP INDEX 2 Device overview 1 2 3 4 5 6 7 8 9 17 16 15 14 13 12 11 10 1 2 3 4 5 6 button, opens the control panel. The way the rocker switch functions depends on the individual menus and operating modes. If pressed briefly during navigation: the active destination is displayed and the last voice output is repeated, entries that are marked with ". . . " in a list will be displayed in their entirety. T button, opens the TRAFFIC menu: TIM function (Traffic Information Memory) and TMC traffic information messages. 9 : ; < = > ? [. . . ] Use the right knob/pushbutton ; to move the selection marker to the TO item. Use the right knob/pushbutton ; to set the distance from your current position at which the traffic jam bypass should end. NEW CALC appears in the title line whilst the route is being calculated. SETTINGS MODIFY ROUTE TRAFFIC AHEAD TRAFFIC AHEAD FROM: 3. 1mi TO: CLEAR 7. 0mi OK Cancelling the traffic jam bypass feature 2 3 Select CLEAR and press the right knob/pushbutton ;. The navigation menu opens again and the route list is recalculated. Excluding a route section from the route list You have the option of excluding individual sections from the calculated route. This is useful if you are informed of road closures or construction sites along your route and you want to avoid these areas. Excluding a route To exclude a route, proceed as follows: 1 2 Press the traffic jam button 7. Note: Longer sections in which you can exclude subsections are marked with a "+". To view the subsections, highlight the entries marked with a "+" and keep the right knob/pushbutton pressed for longer than two seconds. Sections that cannot be excluded (for instance, because there is no available alternative route) are marked with a lock symbol. The traffic jam menu is displayed. INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP INDEX 47 DEUTSCH DEUTSCH DEUTSCH ENGLISH 1 Open the traffic jam bypass menu. INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP INDEX 48 3 Use the right knob/pushbutton ; to move the selection marker to the first road that you want excluded from your route. Use the right knob/pushbutton ; to move the selection marker to the last road that you want excluded from your route. The navigation session is displayed again and the route list is recalculated. NEW CALC appears in the title line whilst the route is being calculated. If you want to cancel an exclusion, select CLEAR; the navigation session is displayed again and the route is recalculated. If you want to change the exclusion, select MODIFY and repeat steps 3 - 6 listed in the "Excluding a route" section. 4 5 6 Cancelling / changing exclusions 1 2 Defining route options You can customise the route to suit your requirements at any time, even during an active navigation session. The configurable parameters are: ROUTE: Choose between the quickest, the shortest or dynamic (DYN. ) navigation with TMC. route, the options route listed below will be hidden from view; the TravelPilot calculates the quickest route whilst taking into account the current traffic messages and automatically tunes into a TMC station. MOTORWAY: You can set whether you want to use motorways during your navigation session. FERRY: You can set the system to be able to use ferries or avoid them. TOLL: You have the option of excluding or including roads for which a toll charge is levied in your navigation sessions. Note: If, for instance, MOTORWAY AVOID is set, and a very long detour would be the result of applying this option, the TravelPilot will instead decide to include motorways in its route calculations. Select the menu item you want to change and press the right knob/pushbutton ;. - CONTINUE INTRODUCTION NAVIGATION RADIO MODE CD MODE CD CHANGER SETUP INDEX 49 DEUTSCH ROUTE OPTION ROUTE DYN. DEUTSCH ROUTE OPTION ROUTE FAST MOTORWAY WITH FERRY WITH TOLL WITH CONTINUE DEUTSCH NAVI. [. . . ] This affects all the settings for the navigation system and the audio sources. Step 1: If a navigation CD is inserted, you will be asked whether you want to reset the navigation system's values. If no navigation CD is inserted, the next query is displayed straight away. 2 2 3 3 If you want to delete the settings, press YES or to retain the navigation system's settings, select NO. [. . . ]