User manual BLAUPUNKT TP DX-N SIL. IBERIA

[. . . ] 19 Installing the GPS antenna . . 5 Installing the display . . . . . . . . . . . 6 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Technical data . . . . . . . . . . . . . . . . . . . 10 Basic navigation unit . . . . . . . . . . . . . . . . . . . . . . . 10 Installing the speaker . . . . . . . . . 6 Installing the control unit . . . 7 What's included in the delivery . . . . . . . . . . . . . . . . . . . . 11 3 Allgemeines Kurzanlei- Zieleingabe Touren Zielspeicher Einstellun- Anhang Installation Description The TravelPilot DX-N navigation system is an independent system with an integrated gyroscope. After a destination has been entered and activated, the system delivers visual driving recommendations as pictograms on a 5" colour monitor and spoken driving information via a separate speaker well in advance of any turns or changes in driving direction required. [. . . ] Depending on the GPS reception available, the calibration is completed after the vehicle has been driven approx. Driving along a winding route (in the city), which is indicated on the monitor on a map, accelerates the calibration. The speedometer signal connection in the vehicle allows the system to determine the distance driven. If there is no speedometer signal, it will be necessary to have a route sensor installed by an authorised customer service centre. In this case, you will have to order a sensor kit (route sensor, magnet strips, bracket, plug and installation instructions) from your dealer. Order No. : 7 607 611 093 Installation Installing the navigation unit Where to install the navigation unit Important!Before inserting the TravelPilot, you have to make sure that the gyroscope is positioned horizontally (see Fig. The TravelPilot DX-N can be installed in the car radio compartment in the vehicle (installation depth 218 mm). For vehicles without a DIN compartment, a universal equipment housing has been included (see Fig. Check to see which method of installation is required for the vehicle and, if necessary, use a vehicle-specific installation kit. If a tuner box or remote control is to be added to the TravelPilot at a later date, the connection wire included (8 604 492 522) could be installed at this point. Before drilling the holes for the mounting screws, make sure that no damage will be done to covered wiring, the petrol tank or fuel lines!Make sure that the vehicle operating elements remain easily accessible and are not obstructed in any way (gear stick, hand brake, etc. )!Important: We assume no responsibility for any equipment that is installed incorrectly and the consequences thereof! Connecting the speedometer signal Important: This connection should be made by an authorised customer service centre. The connection is made with the speedometer signal wire (8 618 841 988) to the vehicle-specific speedometer signal connection. (see connection diagram, page 18). Connecting the back-up lights signal wire Important : This connection should be made by an authorised customer service centre. The connection is made with the back-up lights signal wire (8 618 842 033) to the vehicle back-up lights. Make sure that there are +12V at the connection when the vehicle is backing up (see connection diagram, page 18). Important: We assume no responsibility for any equipment that is installed incorrectly and the consequences thereof! Important installation information for the speedometer signal When connecting the speedometer signal, make sure to observe the following information: 1. Where to find the signal: For many vehicles, the speedometer signal can be found in the vehicle-specific car radio plug. Contact the customer service of the vehicle manufacturer or an authorised navigation dealer to find out what the exact pin allocation is. Do not use the speedometer signal from ABS control units or control circuits. 7 Allgemeines Kurzanlei- Zieleingabe Touren Zielspeicher Einstellun- Anhang Installation Video input assignment The video input socket is intended for future applications. [. . . ] button, select the test menu Pin Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 EXT_R EXT_G EXT_B V_GND EXT_SYNC NC U14 STANDARD SWITCH EARTH NC N. UB Screen switch MP_U53 Input / Ouput E E E E E A E A Comment Red input Green input Blue input Video earth Synchronisation input 5. Now select the required test using the or button, press the OK button and follow the on-screen instructions. If the test was completed successfully, the menu item will be labelled with a tick. [. . . ]