User manual BLAUPUNKT SEATLE CR44

[. . . ] 58 Automatic bandwidth adjustment (SHARX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Deleting CD names/TPM with DSC UPDATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Correcting the clock after the power has been disconnected . . . . . . . . . . . . . . . . . . . . . . . . . 66 Deactivating the hour correction function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To select a station on a different waveband: · Press NEXT as often as necessary until the desired memory bank appears and then select the station by pressing ST1 - ST6. To select a scanned station and switch off Preset Scan: · Press SCA or the rocker switch briefly. Scanning stored stations with Preset Scan You can have all of the stored stations briefly scanned on all wavebands and in the selected FM memory bank. Preset Scan cannot be started unless PTY is switched off ("PTY" is not highlighted in the display). To do so · press TU and switch off the function by pressing the corresponding key. All of the stored stations on the waveband selected and within reception range will be scanned one after the other. "SCAN" and the station name or frequency will flash alternately in the display. You can also scan all of the stations within reception range. Radio Scan cannot be started unless PTY is switched off ("PTY" is not highlighted in the display). To do so · press TU and switch off the function by pressing the corresponding key. All of the stations on the waveband selected and within reception range will be scanned one after the other. "SCAN" and the station name or frequency will flash alternately in the display. The scan time can be set from between five to a maximum of 30 seconds. Please refer to the section on "DSC programming - SCANTIME". Selecting the seek tuning sensiIf necessary, switch off PTY on menu level tivity You can alter the automatic seek tuning sensitivity. If "lo" is displayed, the radio will only pick up strong, local stations (low sensitivity). Displaying the selected program type · Press << or >>. The program type selected last will be displayed briefly. Selecting a program type a) Using the preset buttons When PTY is switched on, you can use the preset buttons ST1 - ST6 to select the program types stored at the factory. If you would like to listen to a station with this PTY, · press / to start the seek tuning function. If the radio is unable to find a station offering the selected program type, the display will show "NO PTY" and a beep tone will be emitted. The radio will select the station which was tuned into before seek tuning was activated. Please refer to the next section on "Storing program types". b) Using the << >> buttons on the rocker switch When PTY is switched on, you can select a program type using buttons << >>. · Press << or >>; the program type selected last will be displayed for 3 seconds. · During this period press >> (forwards) or << (backwards) to select the desired type. If you would like to listen to a station with the selected PTY, · press / to start the seek tuning function. If the radio is unable to find a station offering the selected program type, the display will show "NO PTY" and a beep tone will be emitted. The radio will select the station which was tuned into before seek tuning was activated. [. . . ] If you remove the KeyCard during the reading process, "READ KC" will appear on the display panel. With LED ON, the "ON" knob will flash for extra antitheft protection when the unit has been switched off and the KeyCard removed. PEAK ON/OFF Switches the dynamic level display for the volume on/ off. TOM ON/OFFIf you have a second KeyCard with a Turn-On Message, you can switch off this information with "TOM OFF". [. . . ]