User manual BLAUPUNKT SAVANNAH CR127

[. . . ] FCC Warning The equipment has been tested and found to comply with the limits for a Class B device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with instructions, may cause harmful interference with radio communications. However, there is no guarantee that radio interference will not occur in particular installation. [. . . ] This will prevent them from touching the vehicle or each other and causing a short-circuit and damage to the radio or vehicle. Once the connections have been successfully made, you can begin to mount the unit. SPEAKER CONNECTIONS he unit's Dual-Level Fader allows you to fade between the front and the rear channels using either the front and/or rear speaker leads and/or the rear preamp outputs, providing you tremendous flexibility in configuring your speaker arrangement: · You can connect a speaker (regular, co-axial or tri-axial speakers or component speaker system, all hereafter referred to simply as "speaker") to each of the units' four pairs of speaker leads. · You can connect the 2 RCA preamp outputs to multiple external amplifiers and power multiple speakers or speaker systems through the amplifiers. Connecting the Speaker Leads To prevent short circuits or serious damage to the unit and/or speakers: · Connect the speaker leads only as indicated in the wiring diagram. Disconnect the vehicle battery's negative terminal before making connections. · Only use speakers that have impedance ratings of 4 ohms or higher and have power-handling capabilities greater than the unit's stated power level. · The unit's internal amplifier is designed to handle a 4-ohm load on each pair of speaker leads. · DON'T connect two speakers to a single pair of speaker leads ("in parallel") unless both speakers 6 each have at least 8 ohms impedance. DON'T connect the left and right speaker leads to each other or to the same speakers. Attach the back of the unit to the mounting strap using the support stem bolt and hardware. Bend these tabs Dashboard 8 Mounting the Unit in a Japanese Car You may have difficulty mounting this unit in some Japanese cars that have ISO mounting features (side-bracket mounting systems). 1 Run a blade along the slits on the back of the front trim ring, unscrew the two side screws, and separate it from the unit. Save the trim ring and related hardware in case you ever want to install the unit in another vehicle. 2 Use the vehicle's own mounting hardware to attach the unit. 1 Slit 2 TOYOTA max. size M5x8 Bracket Support 9 Maintenance Removing the Unit Use the Release Keys as shown below. Keep them in a safe place in case you need them in the future. Fuse Replacement When replacing the fuse, be sure to use one with the correct amperage, which will be stated on the fuse case. Never use a fuse that has a stated amperage exceeding the one supplied for this unit, as this could cause malfunction and serious damage to the unit. 10 Specifications Audio Power Specifications Power Output and Total Harmonic Distortion: 13 watts per channel minimum continuous average output into 4 ohms, 4 channels driven, from 30-15, 000 Hz with no more than 1% total harmonic distortion. Other Specifications Tuner FM Tuning Range: Intermediate Frequency: FM Mono Sensitivity: Seek lo sensitivity: Seek sensitivity Selectivity: Signal-to-Noise Ratio: Harmonic distortion at 1 kHz: Separation: Frequency Response: AM Tuning Range: Seek lo sensitivity Seek sensitivity: Intermediate Frequency: Signal-to-Noise Ratio: Frequency Response: 87. 5 - 107. 9 MHz 10. 7 MHz 13 dBf 51 dBf 31 dBf 80 dB at 400kHz 65 dB (stereo), 70 dB (mono) 0. 7% (stereo), 0. 5% (mono) 30 dB 30-15, 000 Hz ± 3 dB 530 - 1, 710 kHz 50 dBµV 25 dBµV 450 kHz 50 dB 30-5, 000 Hz + 3dB Audio Speaker Impedance: Maximum Amp Power: RMS Power: Bass Control: Treble Control: Loud: Preamp Output: 4-8 ohms 4 X 30 Watts (at 4 ohms) 4 X 13 Watts (at 4 ohms) <1% THD ± 10 dB @ 100 Hz ± 10 dB @ 10 kHz + 8 dB @ 60 Hz & + 2 dB @ 8 kHz 4-Channel, Low-Impendance (100 ) Preamplifier Over 3 Volts of Distortion-Free Preamp Output Cassette Signal-to-Noise Ratio: with Dolby B Noise Reduction: Tape Wow and Flutter: Tape Frequency Response: 55 dB 65 dB 0. 10% dB 30-18, 000 Hz + 3 dB 180 x 52 x 155 mm, 7 x 3 x 6 1/8 in. 1. 4 kg (3. 0 lb. ) 12 V DC car battery (11-16 V DC allowable) 15°F to 120°F, ­10°C to 50°C · Unit · Faceplate · Wire Harness, including 2-Channel RCA Preamp Output Harness · DIN Sleeve · Mounting Hardware · Owner's Manual in English, French, Spanish and Portuguese · 4-Channel Preamp Output Harness (Part No. 8634494218) General Dimensions (w/o projecting parts/controls): Mass: Power Requirement (neg. grnd. ): Operating Temperature: Supplied Accessories: Optional Accessories: Design and specifications subject to change without notice. 11 Location of Controls 1. 18. Balance Right Fade to Rear /\ Button Seek and Manual Tuning Clock Hours V Button Seek and Manual Tuning Clock Minutes FM/AM Presets Dolby B Noise Reduction Display Instructions -- General Operation See Traffic Safety & Precautions on page 4. "Press" means a momentary press of less than 1/2 second. "Time Out" When additional button presses are anticipated to complete a procedure, the unit will automatically exit the procedure after 4 seconds of inactivity. 12 Ignition-Off Clock Recall Any button press while ignition off displays time for about 8 seconds. If power was not switched off before face removed, unit will automatically poweron when face is reattached. [. . . ] Unit continuously scans until user stops scan by pressing SCA, another tuning button or SRC. Cassette Tape Player Operation Tape Playback: · Insert cassette into Cassette Door. (Note: Make sure that the side of the cassette exposed is facing right and that all slack has been removed from the tape prior to insertion. ) · If ignition switch is already in "on" or accessory position, insertion of cassette will turn unit on. If unit already turned on, cassette insertion will override other audio source, such as radio. Cassette play will begin, and the display will indicate which tape program is in use, "1" or "2". [. . . ]