User manual BLAUPUNKT RPD 7000

[. . . ] l If no sound comes from the speakers of a two-speaker system, set the fader control to the center position. You are cautioned that any changes or modifications not expressly approved in this manual could void your Warranty. If you have any questions or problems concerning your unit that are not covered in this manual, please contact your Blaupunkt dealer. DETACHABLE FACE Detaching & Attaching the Face: The face of this untt can be detached and taken with you to prevent it from being stolen. Detaching the Face: Press the REL (Release) Button and detach the face by gently pulling it off as illustrated. [. . . ] Intermediate Frequency: 10. 7MHz FM Mono Sensitivity: 6 dBf Seek Sensitivity 22 dBf Selectivity: 60 dB at 400 kHz Signal-to-Noise Ratio: 70 dB (stereo). 0. 5% (mono) Separation: Frequency Response: 30-15, ooO Hz * 0. 75 dB Design and specifications subject to change without notice. AM 530-1. 7lOkHz 531 - 1. 502 kHz (RPD 7000X only) Seek Sens!tiv!ty 31 dBpV lnlermedrate Frequency 450 kHz SIgnal-to-Norse Ratlo 50 dB Audio Speaker Impedance MaxImum Amp Power RMS Power Bass Control Treble Control Loudness Preamp Outputs Preamp Output Voltage 4. 6ohms 4 x 35 Watts (at 4 ohms) 4 x 17 5 Watts (at 4 ohms) +lOdBOlOOHz tl0 dB @ 10 ktiz tlOdB01100Hz &+7dB@0kHz 2. CH RCA 1. 5 volts maximum 8 100% Modulation with < 1% Total Harmonic Distortion Tunmg Range (:D :innal-h-No& R&o: Player *`";l;;; Range: & Frequency Response: Harmonic Distortion: General Drmensions (w/o projecting parts/controls): 176x50x155. 5mm 7 x 2 x 6 in. gmd. ): 12 V DC car battery Operating Temperature: 15°F to 120°F. Faceplate l DIN Sleeve l Mounting Hardware l Owner's Manual in English, French, Spanish and Portuguese 63 dB 90dB 5-20, COO Hz f 3 d6 I 620, 000 Hz f 1 dB . Ol% Note: Make sure that the face is inserted right side up. Do not press hard against the face when attaching it to the chassis, it may be easily attached with gentle pressure Do not expose the face to direct sunlight, heat sources such as hot air ducts or leave it in a humid place. Never leave it on the dash board of a vehicle parked in direct sunlight, where there may be a considerable rise in temperature inside the vehicle. Afffxing Faceplate For Retail Display: The faceplate can be affixed to the unit's chassis, which is desirable for a retail display, for example. This should only be done in situations whom the unit can be accessed from behind the mounting surface. Once the faceplate is affixed, the mlease keys cannot ba used to remove the chassis. To afffx the faceplate, obtain the small bolt (M2. 6~10) from hardware pack and drive it into the upper hole at the left of the chassis using a Phillips screwdriver. (See' rn Fig. 2. ) ELECTRICAL CONNECTIONS AND INSTALLATION @/~?#&*~@I To avoid the aggravation of costly mrstakes and serious damage that could make you feel this way, please carefully read all of the instructions before you begin Carefully follow all instructions. l DON'T connect two speakers to a single pair of speaker leads ("in parallel") unless both speakers each have at least 8 ohms impedance l DON'T connect the left and right speaker leads to each other or to the same speakers. l DON'T connect the front and rear speaker leads to each other or to the same speakers. l DON'T connect any active speakers (with built-in amplifiers) to the speaker leads or unless the speaker's or amplifier's manual states that this is OK. LOCATION OF CONTROLS Loudness Press LO Bu, , on 10 actwafe o, deactwe loudness RADIO OPERATION Automatic Steraaono Reception Adjustment When an FM stereo program with a signal strength of at lea+ 50 dBt is tuned in, the ste, eo indicator ("a") appears in the Display Window. the unit automatically blends the signals, eliminating the noise and gadually converts to the monaural o, "mono" mode. The stereo symbol will disappear from the Display. L_-_. INSTRUCTIONS-GENERAL OPERATION _~___~ Selecting the Band Press the BND bulton as many times as necessan/ to select the desired band. Selactlng FM Tuning Standards: US I European (RPC 435X only) Locate the opening on the bottom of the unit designated wth a label. move the switch in the opening to the desired FM tuning standard as indicated by the label. Press and release the A or V butlon to s&k the next receivable station. To stop seeking and return to the previously tuned Irequency, press the other of the A 0, V buttons. the Tuning Controls , eYe, t 10 Seek T"", "g station scan P, ess Ihe SCN Bulfon 10 ac, , "ate s, a, , on scan Scanned trequencles will blink TO Stop scan press the same butlo" preset scan Press the SCN button for more than 2 seconds to activate preset scan. In the , ad!o mode, the dlsptay pnonty chotces are clock and radio frequency. [. . . ] Repeat Play - Press the RPT (Repeal Play) Bulton to repeat the same selection. CD Scan -Press SCN Button to $ta, t CD Track Scan; start of scan mode is tndlcated by me , , , , , \k, , ~(l 0, Ihe lrack m, mt, e, The - . the unit will automatically return to the volume mode and the display wilt revert back to the p, wity display. You can also p, ess and release AUD as needed to return to the priority dlsptay. AU0 Button Summary . [. . . ]