User manual BLAUPUNKT RPC 4000

[. . . ] l You are cautioned that any changes or modifications not expressly approved in this manual could void your warranty. If you have any questions or problems concerning your unit that are not covered in this manual, please contact your Blaupunkt dealer. FEATURES Congratulations on your PRECAUTIONS . If your vehicle was parked in direct sunlight resulting in a considerable rise in temperature inside the vehicle, DETACHABLE FACE Detaching & Attaching the Face: The face of this unit can be detached and taken with you to prevent It from betng stolen Detaching the Face: Before detaching the face, be sure to press the PWR Button first. Then press the REL (Release) Button and detach the face by gently pulling it off as Illustrated. [. . . ] l If you use the unit's connector with or without an adapter, make sure that function of the leads (wires) of the connector match the function of the leads in the mating connectors!- If your vehicle's radio wire harness is not compatible with this unit's harness connector, you can either a. l We recommend making and testing all electrical connections before installing the unit. Connect the leads (wires) according to instructions and diagram below unless the speaker's or amplifier's manual states that this is O. K. l l ELECTRICAL CONNECTION INSTRUCTfONS Disconnect the vehicle battery's negative terminal before making connections. : Before any other connections are made, you must first connect the antenna in order to avoid damage from mis, viring. 3 Connect speakers following the guidelines in the SPEAKER CONNECTION section below. Connect the black (power ground) lead to a grounded metal part on the vehicle. We recommend grounding all audio system black ground leads (head unit, CD changer, etc. ) to a common grounding point, preferably a non-painted surface under the instrument panel. Connect the yellow (constant power) input lead to a source of constant battery power, preferably a terminal to an appropriate slot in the fuse box. Connect the red (turn-on power) input lead only after the other leads are connected. Be sure to connect the red lead to a positive (+) 12 Volt power terminal that is energized only when the ignition key is set to the on position or accessory position. Tape Wow and Flutter: 0. 10% Tuning Range: 530 - 1, 710 kHz Tape Frequency Response: 50-l 5, 000 Hz * 3 dB Seek lo sensitivitv 55 dBpV General Seek sensitivity: ' 35 dBpV Dimensions (w/o proiectinq parts/controls): 178 x 50 x 153 mm 45" _kH, _ . _ Intermediate Frequency: 7 x 2 x 6 in. 1. 4 kg (3. 0 lb. ) Design and specifications subject lo change withouf notice. gmd. ): 12 V DC car battery Operating Temperature: 15°F to 12O'F. -10°C to 50°C l Untt l Faceolate Supplied Accessories: r l Mounting Hardware * DIN Sleeve l Owner's Manual In English, French, Spanish and Portuguese INSTRUCTIONS - GENERAL OPERATION "Press" means momenlaly press of less than l/Z second Turning Unit On Vehicle lgnlbon must be on To turn unit on. Turning Unit Off Press the PWR Button to turn the u", t off Volume Press + or-to quickly increase or decrease the volume to the desired level. press the other part of the button before the volume level disappears from the display. You can then gradually adjust the volume I" either direction, making precise adjustment easy. Adjustable Turn-O" Volume First adfust the volume to the (maxtmum) volume level dewed when the unit IS turned on Press and hold the PWR Button for more than two seconds The untt turns off and the turn-on volume level IS memowed When the unit 8s turned cm. avan II the unit was turned off while the volume was at a hlgher level However, II the volume IS turned off when the volume level IS lower than the stored TumOn volume level. the volume wit be at the lower level when the untt IS turned back on Setting the Clock Turn tha unll on Press the AUD Button for four seconds until the ckxk starts bltnkmg (The display wtll change after two seconds Ignore thls and c~nbnue to hold for two more seconds ) Once the clock starts blmkmg. Press the A Button to set the hour, and press the V Button to sat the mtnutes (To change the minute lndlcatot to the nearest hour ( 00), you can press the BND Button Press the AUD Button agal" to acttvata tha clock RADIO OPERATION Band Selection Press the BND Button as needed to access the desired band, FMI FMII or AM. [. . . ] The radio will play. Press AU0 Button as needed to select the Balance made. Press the + Button to increase the left speaker output or press the Button to increase the right speaker output to the desired level: Fader Press AU!3 Button as needed to select the Fader mode. The level of output for front and back speakers is indicated in the Display Window. Press the-Button to decrease the front speaker OUIDU~: * five seconds after you complete your adfustments, the untt wll automabcally return lo the volume mode and the display wit revert back to the pnonty dtsplay, clock or funcbon. [. . . ]