User manual BLAUPUNKT RPC 31BLUE

[. . . ] Then press the REL (Release) Button and detach the face by gently pulling it off as illustrated. Be sure not to drop the face when detaching it from the chassis. 1 Attaching the Face: Apply the right hand side of the face to the chassis by sliding (part B) of the face to (part A) at the front of the chassis. Gently push the left side of the face against the front of the chassis until it snaps into place. Do not press hard against the face when attaching it to the chassis, it may be easily attached with gentle pressure. [. . . ] Once the connectrons have been successfully made, you can begin to rnstall the unit. SPEAKER CONNECTtONS l You can connect a speaker (regular, co-axial or trt-axial speakers or component speaker system, all hereafter referred to simply as "speaker") to each of the units' four pairs of speaker leads, Connecting the Speaker Leads To prevent short circuits or serfous damage to the unit and/or speakers: * Connect the speaker leads only as indicated in the wiring diagram. * Only rrsn sponknrs lhnt hnvn irnpodnncn rntings of 4 ohms or higher and have power-handling capabilities greater than the head unit's stated power level. - The unit's internal amplifier is designed to handle a 4-ohm load on each pair of speaker leads. l DON'T connect two speakers to a single pair of speaker leads ("in parallel") unless both speakers each have at least 6 ohms impedance. * DON'T connect the left and right speaker leads to each other or to the same speakers, * DON'T connect the front and rear speaker leads to each other or to the same speakers. l DON'T connect any active speakers (with built-in amplifiersjto the speaker leads, Addlng CD Changer: You can easily play compact discs through this unit by adding the Blaupunkt CDC-RF6 6-Disc Compact Disc Changer. The space-saving CDC-RF6 easily plugs into the unit's antenna jack and comes complete with its own commander control. See your Blaupunkt dealer for details! INSTALLATION l l Recommendations Carefully choose the mounting location so that the unit won't interfere with normal driving. Avord mounting locations where the unit would be subject to high temperatures, such as from direct sunlight or hot air from the heater, or vibration. l where it would subject to dust, dirt or excessive l The illustration below shows a typical installation, however, you may need to adjust the installation, depending on the unit. If you have questions or need additional installation hardware, consult your Elaupunkt dealer. Make sure the unit is firmly anchored (preferably at both front and back) Mounting The Unit In Most Dashboards and does not vibrate. 2 Select and bend the appropriate tabs to hold the sleeve firmly in place. Attach the Mounting Strap to the underside of the dashboard, using screw. Anach the back of the unit to the mounting strap using the support stem bolt and hardware, Mounting the Unit in a Japanese Car You may have dtffrculty mountrng this unit in some Japanese cars In thus case, consult your Blaupunkt dealer. I I Bend these tabs Removing the Unit Use the Release Keys as shown below. In me tuture. MAINTENANCE Fuse Replacement When replacrng the fuse, be sure to use one with the correct amperage. Never use a fuse that has a stated amperage exceeding the one supplred for thus unrt. as thus could cause malfunctron and serious damage to the unrt. SPECIFICATIONS Audio Power Soecifications Power Output end Total Harmonic Distortion: 10 watts per channel mrnimum continuous average output into 4 ohms, 4 channels driven, from 30-15000 Hz with no more than 1% total harmonrc drstortron. Othefipe&!cati. oqe Tuner FM Tuning Range: lntennedrate Frequency: FM Mono Sensrtrvrtv: Selectivity: ' Signal-to-Noise Ratio: Harmonic distortion at 1 kHz: Separation: Frequency Response: AM Tuning Range: Seek lo sensrtivrty Seek sensrtivrty: lntermedrate Frequency: SIgnal-to-Noise Ratro 87. 5 - 108. 0 MHz 07. 5 - 107. 9 MHz 10. 7 MHz 18 dBf 75 dB at 400 kHz 65 dB (stereo), 70 dB (mono) 0. 7% (stereo), 0. 5% (mono) 30 dB 30-l 5, 000 Hz f 3 dB 531-l , 602 kHz 530-1. 710 kHz 55 dBuV 35 dBpV 450 kHz 45 dB Audio Speaker Impedance: Maximum Amp Power: RMS Power: Bass Control: Treble Control: Cassette Signal-to-Noise Ratio: Tape Wow and Flutter: Tape Frequency Response: 4-0 ohms 30 Watts x 4 (at 4 ohms) lOWattsx4 ilOdB@ 100Hz ilOdB@ 10kHz 53 dB 0. 10% 50-15. 000 Hz f 3 dB Des!gn and Specifications subject to change wrthoui nobce. General Dimensions (w/o projecting parts/controls): 170 x 50 x 153. 5 mm 7 x 2 x 6 in. grnd. ): 15°F to 12o"F, -10°C to 50°C Operating Temperature: l Unit l Faceplate Suppked Accessones: . [. . . ] You can also press and release AUD as needed to ret&" to iOLUME, which appears alfer FADER t" the AUD Button cycle * AfJD Baton Summary * Pressing and releasing the AUD Button accesses these modes in this succession: * Temporary Display Change(s). * Pressmg the AUD Button for two Seconds changes the display priority between clock and funchon. * Pressmg the AUD Button for tour seconds accesses the time adjustment mode. * While I" any AUD mode, it no button is pressed for five seconds, the unit returns to the volume adjustment mode and priorlfy display. TROUBLESHOOTING GUIDE The fOffOw+"g check Will aSSlSf I" the COrreCtlO" of mOSf problems which you may encounter wfh your unit. [. . . ]