User manual BLAUPUNKT RPC 3000

[. . . ] Do not expose the face to direct sunlight, heat sources such as hot air ducts or leave it in a humid place. Never leave it on the dash board of a vehicle parked in direct sunlight. where there may be a considerable rise in temperature inside the vehicle. Affixing Faceplate For Retail Display: The faceplate can be affixed to the unit's chassis, which is desirable for a retail display, for example. [. . . ] l Be sure to detach the faceplate before you start to connect or install the unit. l If you use the unit's connector with or without an adapter, make sure that function of the leads (wires) of the connector match the function of the leads in the mating connectors!l If your vehicle's radio wire harness is not compatible with this unit's harness connector, you can either a. cut off the unit's connector and use a different type of connection. - We recommend making and testing all electrical connections before installing the unit. - Connect the leads (wires) according to instructions and diagram below unless the speaker's or amplifier's manual states that this is O. K. ELECTRICAL CONNECTION INSTRUCTIONS - ff vou cannot use the unit's connector with or without an adapter. 1 Disconnect the vehicle battery's negative terminal before making connections. Connect speakers following the guidelines in the SPEAKER CONNECTION section below. 3 Connect the black (power ground) lead to a grounded metal part on the vehicle. We recommend grounding all audio system black ground leads (head unit, CD changer, etc. ) to a common groundrng point, preferably a non-painted surface under the instrument panel. Othefipe&!cati. oqe Tuner FM Tuning Range: lntennedrate Frequency: FM Mono Sensrtrvrtv: Selectivity: ' Signal-to-Noise Ratio: Harmonic distortion at 1 kHz: Separation: Frequency Response: AM Tuning Range: Seek lo sensrtivrty Seek sensrtivrty: lntermedrate Frequency: SIgnal-to-Noise Ratro 87. 5 - 108. 0 MHz 07. 5 - 107. 9 MHz 10. 7 MHz 18 dBf 75 dB at 400 kHz 65 dB (stereo), 70 dB (mono) 0. 7% (stereo), 0. 5% (mono) 30 dB 30-l 5, 000 Hz f 3 dB 531-l , 602 kHz 530-1. 710 kHz 55 dBuV 35 dBpV 450 kHz 45 dB Audio Speaker Impedance: Maximum Amp Power: RMS Power: Bass Control: Treble Control: Cassette Signal-to-Noise Ratio: Tape Wow and Flutter: Tape Frequency Response: 4-0 ohms 30 Watts x 4 (at 4 ohms) lOWattsx4 ilOdB@ 100Hz ilOdB@ 10kHz 53 dB 0. 10% 50-15. 000 Hz f 3 dB Des!gn and Specifications subject to change wrthoui nobce. General Dimensions (w/o projecting parts/controls): 170 x 50 x 153. 5 mm 7 x 2 x 6 in. grnd. ): 15°F to 12o"F, -10°C to 50°C Operating Temperature: l Unit l Faceplate Suppked Accessones: . DIN Sleeve l Mounting Hardware l Owner's Manual in English, French, Spanish and Portuguese INSTRUCTIONS - GENERAL OPERATION "Press" means momenfaly press of less than l/Z second Turning Unit 0" Vehicle lg", f, on must be on To fur" unlf on. press PWR Buffon Turning Unit Off Press the PWR Buffon to turn the umf off Volume Press + or - to qutckly tncrease or decrease the volume to the dewed level The volume level IS tndrcafed I" the Display Wmdow To make a ftne adfusfmenfs to the volume level, press the other part ol the buffon before the volume level dwppears from the dwplay You can the" gradually adjust the volume I" elfher dIrecton, maklng prease adfusfmenf easy Adjustable Turn-On Volume Flrsf adfusf the volume lo the (maximum) volume level desired when the unit is fumed on. However, If the volume 8s fumed off when the volume level is lower than the stored Tum0" volume level. the volume will be at the lower level when the unit is turned back on. Ignore this and continue to hold for two more seconds. ) Once the clock stalls blinking. Press the A Button to set the hour, and press the V Button to set the minutes. you can press the BND Burton. ) Press the AUD Button again to activate the clock. Changing the Information Displayed * To change the dlspfsy priority in the radio mode from cloCk to luncfion 01 function to clock, press the AUD Button lor two seconds. l To change the display temporarily in the radio mode from CloCk to function or function to clock, press and release the AUD Button: After five seconds, the display changes back to the priorafy Information. [. . . ] The change in direcfiw and I" tape program will be conlwmed in the Display. Fast Winding of Tape No matter which side 01 the tape that is playing: * To fast-forward the tape. The direcflon arrow stays on and the oppos~fe arrow blinks to conilrm the last-rewnding. The radio will play. * Fader Press AUD Button as needed to select the Fader mode The level ot output for front and back speakers IS lnduxfed I" the Dasplay Wmdow Press the + Buffo" to decrease the rear speaker output Press the - Button to decrease the front speaker output * Five seconds affer you complete your adjustments, the unit wll automatically return to the volume mcde and fhe dlsplav wll reverl back to the Driorlfv display, clock or function. [. . . ]