User manual BLAUPUNKT RHODOS CC 25

[. . . ] 2 / rocker switch Radio: Automatical station tuning Coding: Read first the "Anti-theft coding" chapter. 5 lo rocker switch Use this button to alter the sensitivity of the automatic station seek operation. lo lights up > - normal sensitivity no indication - high sensitivity Additional function of the lo rocker switch: Switching from stereo to mono: Press longer than 2 seconds. 6 Cassette operation button FF - Fast Forward operation Start/stop: Press FF button briefly. [. . . ] - Press preset button 2 five times, "500" appears in the display. - Press preset button 3 twice, "520" appears in the display. To confirm the code number: Press the upper part of the rocker switch . Wrong code number entered It should not be possible for thieves to ascertain the code number by trial-and-error. This is why the set will be blocked for a certain period of time, if an incorrect code number is entered. This waiting time is 10 seconds after the first three attempts, and 1 hour following subsequent attempts. After 19 unsuccessful attempts, "OFF" will appear in the display and the set can no longer be restarted. Note: Keep you car radio passport with the code number in a safe place in order to avoid "unauthorized access" to your car radio. If the power supply to the radio is interrupted while the code system is switched on, you need to know the right code number. Switching the code system on Precondition: The radio must be connected to permanent power. · · Hold down the preset buttons 1 and 4 simultaneously. · 15 PORTUGUES Your car radio is now ready for operation. If three dashes appear again in the display, you have entered a wrong code number. Now it is essential to enter the correct code after the waiting period has elapsed (COD in the display). ESPAGÑOL · Release preset buttons 1 and 4. "COD" will be briefly displayed each time the radio is turned on. SVENSKA NEDERLAND ITALIANO FRANÇAIS ENGLISH DEUTSCH Amplifier Section If the radio is turned off before the waiting period has elapsed, then the waiting period restarts as soon as the radio is turned on again. Radio Section Selecting the Desired Waveband With this set you can listen to FM stations of the frequency band from 87. 5 to 108 MHz. ON/OFF For switching the set on, · turn button 1 . Your stereo is now ready for operation. Switching the code system off · · · · Turn off the radio. "COD" will appear in the display. For switching the set off, · turn button 1 . Tuning in a Station Automatically Tuning in the Following Station · Press the upper part of the rocker switch / 2. Tuning in the Previous Station · Press the lower part of the rocker switch / 2. The car radio automatically starts searching for the previous station. If the rocker switch / 2 up/down is kept depressed, the station seek operation continues to be carried out quickly in the corresponding direction. Balance Control Use button C to balance the sound impression of the right and left channel speaker. Enter the code number given in the Blaupunkt car radio passport and confirm: See example "Restart following interruption . . . ". The code system is now deactivated. Sound Control Use the TONE button D to adjust the sound according to your personal preference. Manual Tuning All stations can also be tuned in "manually": · Press the rocker switch <</>> 3 on the left or the right. The frequency band is scanned in small steps. 16 Adjusting the Station Seek Sensitivity With this set you can modify the station seek sensitivity. If you want to search for strong stations only (reduced sensitivity): · Press the lo rocker switch 5 until "lo" lights up on the display >. If you also like to search for weaker stations (increased sensitivity): · Press the lo rocker switch 5 until the "lo" indication > goes off. Memorizing a Station You can memorize a station with each of the preset buttons B. [. . . ] · Insert the cassette into the slot with the tape side showing to the right and the empty reel to the front. Fast Forwarding the Tape Fast Forward Operation · Briefly press the FF button 6. Stopping Fast Forward Operation · Briefly press the FF button 6. 19 PORTUGUES ESPAGÑOL SVENSKA When leaving the coverage area of the tuned in traffic station, your car radio will automatically start searching for a new traffic station while you are listening to your tape. To stop tape play: · Press the button 6 firmly. The cassette is ejected. NEDERLAND Automatic Start of the Station Seek Operation (Tape Playback) Removing the Tape ITALIANO FRANÇAIS DEUTSCH Appendix Care Notes We recommend C-60 and C-90 type tapes for use in any automobile tape player; to protect your tapes, store them in a cool place away from dirt, dust, or excessive temperatures above 50° Celsius. In order to ensure smooth tape operation, cold tapes should be allowed to heat up a bit before they are played. [. . . ]