User manual BLAUPUNKT NAVPACK RGN 08 GB 5

[. . . ] 4 Connecting the back-up light signal cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Distance calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Installing the wheel sensor and the magnetic stri4 (only for vehicles without a speedometer signal) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Installing the wheel sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Mounting the magnetic strip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Installation tolerances for the wheel sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Due to automatic length adaptation, the magnetic strip must be applied to the non-driven left-hand wheel. The system recognises driving forwards and backwards by evaluating the back-up signal (forwards = 0 volts, backwards = 12 volts) received via the connection contact (RFLS) provided for that purpose. -3- Negative connection Screw the negative cable (brown) directly onto the chassis. Scratch the contact point for the ground down to the bare metal and grease it with anti-seize graphite petroleum (important for good grounding). Connecting the GPS antenna Safety instructions Mount the antenna only on a metal roof with magnetic properties (not suitable for aluminium). Do not mount the antenna on roofs covered with leather or synthetic materials. When mounted on a roof (held only by a magnet), the antenna must not be exposed to temperatures of less than -20 °C or more than +80 °C. 8 622 401 437 If necessary, use protective sheathing to protect the antenna cable from being pinched. The adherent surface of the antenna must be free of dirt, snow, ice, etc. If the antenna is painted the same colour as the vehicle, this may have an adverse effect on the reception, especially if paints containing a high percentage of metal are used. We assume no guarantee that the antenna will operate properly after it has been painted. On notchback vehicles, attach the antenna to the boot lid using the mounting brackets. Depending on the thickness of the metal, use the corresponding headless screws, Fig. On estate and hatchback cars, affix the antenna to the roof with its magnetic foot, Fig. For estate and hatchback cars, lay the antenna cable along the rain gutter downwards and into the interior of the vehicle. Any obstacles near the antenna, such as roof racks or bicycle carriers, may have an adverse effect on or even obstruct satellite reception. Route the antenna cable into the interior of the vehicle and connect the plug on the antenna cable with the antenna jack on the basic unit. It is advisable to remove the antenna from the roof when driving through a car wash. If the GPS antenna is mounted inside the vehicle, there is no guarantee that the system will function correctly. The connection is made with the back-up light signal cable, see parts included in the delivery, item :, yellow plug to yellow jack of the sensor adapter cable (item 8) to the vehicle back-up light. Make sure that this connection is charged with + 12 V when the vehicle is reversing. Important: We assume no liability for equipment which has been connected incorrectly and any consequential damages! Distance calibration After the completion of all installation and connection work, it is necessary to perform a distance calibration. Insert the navigation CD into the basic unit and access the Service Menu. When the calibration has been completed, the main menu will ap-pear on the screen. Your RGN 08 will be ready for operation if at least 3 satellites can be received (approx. 10 minutes of operation after start-up). Installing the wheel sensor and the magneticstrip Only for vehicles without a speed signal. [. . . ] - System- diagnosis - Navigation Leaving the service menu(reactivate standby time!) System diagnosis - Calibration values - Error memory - Hardware test - Sensor test - Strech calibr. - GPS status - Keyboard test Leave the system diagnosis level by pressing the TIM button. Leave the system diagnosis level by pressing the TIM button. Subject to modification! 8 622 401 437 -6- Scope of delivery 1 Navigation unit with integral gyro and GPS receiver 2 GPS-antenna 3 Fixings 4 8 618 841 985 Adapterkabel voor sensor- interface, ca. 25 cm 2 5 8 618 841 412 DC cable, 6 m 1 6 8 618 842 033 Reversing light cable, 4. 5 m (RFLS) 3 7 8 618 841 988 Speedometer signal cable, 4, 5 m 8 618 841 105 8 8 618 842 265 Can- adapter wiring 9 8 618 841 525 Can cable 6m : 8 618 841 491 Cinch cable (NF) 6m 2 916 064 005 (4x) 2 910 645 120 (4x) 8 618 841 423 (58 x 13) 8 600 660 007 (6x) 8 618 841 421 (58 x 9) 4 8 622 401 437 -7- 5 8 6 9 gelb 7 : weiß Technical data Basic navigation unit 8 618 841 994 with integrated gyro, GPS receiver and CD-ROM player Rated voltage (Urat) Rated current (I) Stand-by current Speech output/volume Time to first position computation CD-ROM drive Operating temperature Mounting orientation Width Height Depth Weight 14 V DC Typically 0. 55 A (Imax 1. 05 A) Typically 0. 35 A Max. 3 Watt/4 Ohm (Warm start, memory refresh) < 2 minute; (cold start, memory clear) < 15 minutes For 12 cm CD to DIN EN 60908 only -15°C to +60°C Horizontal/+5° 184 cm 73 cm 171 cm 1. 9 kg 8 622 401 437 -8- Fig. 1 Fig. [. . . ]