User manual BLAUPUNKT MONTEREY CDM83

[. . . ] 27 Sampling all stations to be received with Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Switching the audio source with SRC (Source) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Re-start following an interrup-tion of the power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Switching to changer operation with SRC on the car radio . . . . . . . . . . . . . . . . . . . . . [. . . ] In this case you can no longer re-start the unit. DEUTSCH Anti-theft protection · Release preset buttons 1 and 4. The display will briefly show "CODE" each time the set is turned on. If you have entered the correct code, the unit will now be ready for use. If the display shows "CODE ERR", you have entered a wrong code. Re-enter the correct code after the waiting time ("CODE" will appear in the display). If you switch off the set while it is blocked, the waiting time will start anew as soon as the radio is turned on again. Optical indication for extra security To indicate that your unit is equipped with security coding, you may let an LED installed in the non-detachable part of the front panel flash for extra security when the car is stationary. For this, the following requirements must be fulfilled: Permanent 12 V supply and the + ignition lead must be connected correctly (as illustrated in the installations instructions). Read "DSC programming - CODE-LED". Re-start following an interruption of the power supply (coding system is activated) · · · Turn on the radio. Enter the code number given in the Blaupunkt car radio passport: Example: The code number is 2521. "SEARCH" will disappear from the display when the alternative frequency has been found or after the frequency band has been run through completely. If the reception quality of the selected programme becomes too bad: · Tune into another station. Selecting a waveband With this car radio you can select between the following wavebands: FM 87. 5 - 108 MHz MW 531 - 1602 kHz LW 153 - 279 kHz · Select the desired waveband by pressing the FMT or M·L button. To switch between MW and LW: · Press M·L. REG - regional programme Certain radio programmes are split up at times into regional programmes offering local information. To select a station currently being scanned and switch off Preset Scan: · Press SC briefly. Selecting the seek tuning sensitivity You can alter the automatic seek tuning sensitivity. If "lo" is displayed, the radio will only pick up strong, local stations (low sensitivity). If "lo" does not light up, the radio will also pick up weaker, distant stations (high sensitivity). The degree of sensitivity can be altered in both modes (see also chapter "DSC programming, LOCAL and DIS"). Recalling stored stations You can recall any stored station at the touch of a button. On FM, also choose the corresponding memory bank by pressing the FMT button as many times until the desired bank appears in the display. · Press the corresponding preset button briefly to recall the station. 27 PORTUGUÊS Beginning with the station currently tuned in, you can scan the waveband. To start the scan: · Press SC briefly. ESPAÑOL Sampling all stations to be received with Scan SVENSKA NEDERLANDS ITALIANO The scanned frequency or the station name will start flashing in the display. During the actual scanning process "SCAN" will be displayed. To select a station currently being scanned and switch off the scan function: · Press SC briefly. If no station is selected, the scan function will be automatically switched off after the frequency band has been run through completely. The unit will tune in the station listened to before starting the scan. FRANÇAIS ENGLISH DEUTSCH Receiving traffic programme stations with RDS-EON Switching from stereo to mono (FM) If reception is poor, you may get better sound quality by switching to mono: · Press the lo button for approximately 2 seconds. [. . . ] To switch over: · Press the SRC button. / Select function Adjust value ­ Adjust value + LOCAL (lo) To adjust the seek tuning sensitivity for local reception. LOCAL 1 - high sensitivity LOCAL 3 - low sensitivity 30 BEEP Confirmation tone for all functions which require a button to be pressed for more than 2 seconds. (0 = off) Each alteration of this value is confirmed by a beep tone of the corresponding volume. LED 1 - LED always flashes when the unit has been switched off via the ignition. [. . . ]