User manual BLAUPUNKT MUNCHEN RDM 169

[. . . ] Radio / CD München RDM 169 US Operating instructions 1 2 3 4 5 13 12 11 10 9 8 7 6 19 14 15 2 18 21 1 3 20 17 16 2 Condensed instructions . . . . . . . . . . . . . . . . 12 Read the following before using the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Paging through the transmission chains (FM only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Automatically saving the strongest station with Travelstore . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Proceed as follows: · Press TU and disable PTY using the PTY key. All stored stations on the frequency band which can be received are sampled briefly in turn. "SCAN" and the flashing station name/frequency appear alternately on the display. Selecting sampled stations/terminating Preset Scan: · Press SCA or one of the rocker keys briefly. Calling up stored stations Automatically saving the strongest station with Travelstore You can store the six strongest FM and AM stations in the current reception region automatically in the order of field strength. The six strongest FM stations are automatically stored on the "T" (Travelstore) memory level. If fewer than six stations can be received, four lines appear through the memory locations which are not occupied. When the procedure has been completed, the strongest station (ST 1) is selected. Stations can also be stored manually on the Travelstore level if required (see "Storing stations"). AM, AMT You can call up the stations on the selected frequency band directly: · Press the keys ST1 - ST6. Calling up stations on the other frequency band: · Press NEXT: the other frequency band is displayed. Then select the stored stations using ST1 -ST6. 18 Sampling stations with Radio Scan You can sample briefly the stations which can be received on the selected frequency band. Radio Scan can be started only when PTY is deactivated ("PTY" is not lit on the display). All stations on the frequency band which can be received are sampled briefly in turn. "SCAN" and the flashing station name/frequency appear alternately on the display. Selecting a sampled station/deactivating Scan: · Press SCA or one of the rocker keys briefly. If a station is not selected, Scan is switched off automatically when the seek function has passed through the complete frequency range. · Changing the sampling time (Scan) The sampling time can be selected between 5 and 30 seconds. If you wish to change the duration of the sampling time, refer to "Programming with DSC ­ SCANTIME". Toggling between stereo and mono (FM) You can toggle between stereo and mono in the DSC menu. If you wish to switch to mono, refer to "Programming with DSC ­ STEREO/ MONO". The state selected appears briefly on the display. Changing the sensitivity of the seek run You can change the sensitivity of the automatic seek run. If "lo" is displayed, seek only recognizes stations with good reception (low sensitivity). If "lo" is not displayed, seek also recognizes stations with poorer reception. To adjust the sensitivity, refer to "Programming with DSC ­ FM/AM Sens". Automatic bandwidth switching (SHARX) You can activate automatic bandwidth switching on the FM band by means of the SHARX function in the DSC menu. [. . . ] Should you remove the KeyCard during the read process, "READ KC" appears in the display. NEDERLANDS BEEP Confirmation signal for functions which require a key to be held down for approx. The volume can be selected from 0 to 9 (0 = off). This function enables you to teach in a second KeyCard. Refer to the instructions under "KeyCard anti-theft protection system": "Teaching in a second KeyCard". ITALIANO CLK ON/OFF The time can be displayed with the ignition on and the unit switched off. Select CLK ON in this case. FRANÇAIS 12/24H MODE Select the time display (12-hour or 24-hour). AUX ON/OFF This menu item does not appear when a CD changer is connected. [. . . ]