User manual BLAUPUNKT MNCHEN CD 43

[. . . ] Operating instructions München CD 43 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 1 24 9 a b 23 9 22 a 21 20 19 18 ml kj h g d i fe dc 2 RADIO 3 CD 4 3 Table of contents Important information . . . . . . . . . . . . . . . . . . 26 Setting the volume for the audible alarm and the traffic messages . . . . . . . . . 26 Traffic messages during CD operation26 Automatic start of seek tuning operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Important Information Road safety Being the driver of a motor vehicle you should dedicate your full attention to the traffic around you. [. . . ] To memorise a station proceed as follows: If you wish to store an FM station choose the desired storage level by pressing the FM·T button D as many times as required. Use rocker switch / F to tune in to a station/frequency of your choice. 22 To memorise it press any of the preset buttons ;, <, =, > or @ until the radio resumes play again (takes approximately 2 secs. ). Go through this procedure again if you want to memorise further stations on the other preset buttons and possibly on all wavebands and FM storage levels. If seek tuning locks onto a station stored already, the corresponding preset button will be indicated in the display for approximately 5 secs. (for FM stations the respective storage level will also be shown in display 9 j, k). using manual tuning To tune in to a station and store it you can also use rocker switch << >> G. Choose the desired waveband by pressing either the FM·T button D or the M·L button B. If you want to memorise an FM station, choose the storage level via the FM·T button D. Use the << >>> rocker switch G to tune in to the station/frequency of your choice. Store this frequency by pressing the corresponding preset button until the radio resumes play again. When tuning in to a station that has not been stored and turning the set off, this station will again be played as soon as the set is turned on again. using Travelstore With the Travelstore function you can let the set automatically store the 5 strongest FM stations of the respective reception area and have them sorted according to their field strength. To activate the automatic station storage press the FM·T button D for approximately 2 secs. If required, stations can also be manually memorised on the Travelstore level. You can store different stations on KeyCards 1 and 2. 23 PORTUGUES Adjusting the seek tuning sensitivity The seek tuning sensitivity can be adjusted in two different ways: a) With the lo button 8: Display 9 h shows you the corresponding setting. "lo" stands for normal seek tuning sensitivity (local or nearby stations). "dx" stands for stands for highly sensitive seek tuning (distant stations). pressing the DSC button 7. This function can be separately programmed for KeyCards 1 and 2. Selecting a track As soon as the disk is inserted, the activated CD functions are shown in display 9. If the "TPM" indicator 9 f is off, all CD tracks will be played. If "TPM" 9 f is on, only the tracks programmed with TPM will be played. For information on how to programme the desired tracks read through section "Storing tracks with TPM". Rocker switch pressed ­ Tracks will be skipped. ESPAGÑOL SVENSKA NEDERLAND Mono switchover Your new car radio is equipped with a Blaupunkt FM tuner, which offers you the best possible reception quality. [. . . ] b) Switch off the priority for traffic stations by pressing the ARI button C. Setting the volume for the audible alarm and the traffic messages Should you wish to listen to traffic messages only, you can turn down the volume of the set and stay on standby at the same time. As soon as a traffic info comes in, it will be automatically put through at a preadjusted volume, no matter if you have turned down the volume completely or if you are listening to a CD. You can use the set's DSC software to match the message volume to your special requirements (e. g. [. . . ]