User manual BLAUPUNKT MIAMI 100 USB

[. . . ] In case of doubt, stop at a suitable location and operate your device while the vehicle is standing. · Always listen at a moderate volume to protect your hearing and to be able to hear acoustic warning signals (e. g. General safety notes Observe the following notes to protect yourself against injuries: · Do not modify or open the device. The device contains a Class 1 laser that can cause injuries to your eyes. Cleaning notes Solvents, cleaning and scouring agents as well as dashboard spray and plastics care product may contain ingredients that will damage the surface of the car sound system. [. . . ] The use of straight plugs or adapters leads to an increased risk of injury. Connect/disconnect USB stick. 5 Note The supplied USB cable must be connected to the USB socket on the rear of the unit (see section "Installation" overleaf ). · Gently insert the CD with its printed side uppermost into the drive until you feel some resistance and the CD is drawn in automatically. Note If a CD is ejected and not removed, the drive will automatically draw it back in again after approx. Insert the jack plug of the external device into the front AUX IN socket. · · Switch of the car sound system so that the data carrier will be correctly registered and unregistered. Connect the USB stick to the USB cable or pull the USB stick off. Function Select previous/next track. Select Repeat option: Repeat current track: `RPT TRACK' `RPT DIR' Repeat current folder2: Resume normal playback: `RPT OFF' Select Mix option: Mix all tracks on CD: `MIX ALL' `MIX DIR' Mix current folder2: Resume normal playback: `MIX OFF' Scan all tracks on CD. 3 Cancel scanning at current track. Select display mode: CDDA: CD text (if available) Track number and total time Track number and elapsed time MP3/WMA: Song name (if available) File name Elapsed time Artist (if available) Album (if available) · · · · · · Action Press the / button briefly. Press the 4 RPT button once or repeatedly. · Press the 5 MIX button once or repeatedly. · · · Press the MENU button for more than 1 second. Press the DISP button once or repeatedly. 1 2 3 4 5 Only if the memory bank is switched on (BAND submenu in the TUNER SET menu, see section "Menu settings" overleaf ). Only if CD is inserted or USB stick is connected (Miami 100 USB only) or external audio source is connected. Only if automatic dimming is switched off (DIM setting in the VARIOUS menu, see section "Menu settings" overleaf ). Only if priority for traffic announcement is switched on (TRAF setting in the TUNER SET menu, see section "Menu settings" overleaf ). Only Miami 100 USB. 1 1 2 Only in tuner regions USA and S AMERICA. Each track is played for 10 seconds. Menu settings Menu navigation · Press the MENU button to enter or exit the menu. · Press the / button to select a menu item of the current menu. Making settings If the current menu level shows a value that can be set, this value is flashing in the display. In the table below bold characters (e. g. : ON/OFF) indicate available settings. Underlined characters (e. g. : HI6) indicate factory settings. Code protection This car sound system is protected against theft with a four-digit code number (default code number: 0000). If the code query is activated, the code number must be entered after every interruption of the power supply from the vehicle battery. Activating/deactivating the code query and changing the code number To be able to activate/deactivate the code query or to change the code number, you must also enter the four-digit code number. [. . . ] To switch between hours (HH) and minutes (MM) or vice versa press the Removal or button. Switching on or off the demo mode. Wavebands in the US: Wavebands in South America: FM frequency response: CD Frequency response: Pre-amp out 4 channels: Input sensitivity Front-AUX-IN: Dimensions and weight W x H x D (mm): Weight: TUN AREA EUROPE/USA/ THAILAND/ S AMERICA PRESS UP TO CONFIRM CODE XXXX · · Selecting the tuner area, the device should be operated in. Press the button to confirm. NORMSET CODE SET Restoring factory settings. Switching on or off code protection and changing the code number (see section "Code protection"). C1 178 x 51. 5 x 150 approx. [. . . ]