User manual BLAUPUNKT MESA CR67

[. . . ] FCC Warning The equipment has been tested and found to comply with the limits for a Class B device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with instructions, may cause harmful interference with radio communications. However, there is no guarantee that radio interference will not occur in particular installation. [. . . ] We recommend grounding all audio system black ground leads (head unit, external amplifier, etc. ) to a common grounding point, preferably a non-painted surface under the instrument panel. Connect the yellow (constant power) input lead to a source of constant battery power, preferably a terminal to an appropriate slot in the fuse box. Connect the red (turn-on power) input lead only after the other leads are connected. Be sure to connect the red lead to a positive (+) 12 Volt power terminal that is energized only when the ignition key is set to the on position or accessory position. This will prevent them from touching the vehicle or each other and causing a short-circuit and damage to the radio or vehicle. Once the connections have been successfully made, you can begin to mount the unit. SPEAKER CONNECTIONS The unit's Dual-Level Fader allows you to fade between the front and the rear channels using either the front and/or rear speaker leads and/or the rear preamp outputs, providing you tremendous flexibility in configuring your speaker arrangement: · You can connect a speaker (regular, co-axial or tri-axial speakers or component speaker system, all hereafter referred to simply as "speaker") to each of the units' four pairs of speaker leads. · You can connect the 2 RCA preamp outputs to multiple external amplifiers and power multiple speakers or speaker systems through the amplifiers. Connecting the Speaker Leads To prevent short circuits or serious damage to the receiver and/or speakers: · Connect the speaker leads only as indicated in the wiring diagram. Disconnect the vehicle battery's negative terminal before making connections. · Only use speakers that have impedance ratings of 4 ohms or higher and have power-handling capabilities greater than the receiver's stated power level. · The unit's internal amplifier is designed to handle a 4-ohm load on each pair of speaker leads. Attach the Mounting Strap (2) to the underside of the dashboard, using screw. Attach the back of the unit to the mounting strap using the support stem bolt and hardware. Bend these tabs Dashboard 8 Mounting the Unit in a Japanese Car You may have difficulty mounting this unit in some Japanese cars that have ISO mounting features (side-bracket mounting systems). 1 Run a blade along the slits on the back of the front trim ring, unscrew the two side screws, and separate it from the unit. Save the trim ring and related hardware in case you ever want to install the unit in another vehicle. 2 Use the vehicle's own mounting hardware to attach the unit. 1 Slit 2 TOYOTA max. size M5x8 Bracket Support 9 Maintenance Removing the Unit Use the Release Keys as shown below. Keep them in a safe place in case you need them in the future. Fuse Replacement When replacing the fuse, be sure to use one with the correct amperage, which will be stated on the fuse case. Never use a fuse that has a stated amperage exceeding the one supplied for this unit, as this could cause malfunction and serious damage to the unit. 10 Specifications Audio Power Specifications Power Output and Total Harmonic Distortion: 5. 5 watts per channel minimum continuous average output into 4 ohms, 4 channels driven, from 30-15, 000 Hz with no more than 1% total harmonic distortion. Other Specifications Tuner FM Tuning Range: Intermediate Frequency: FM Mono Sensitivity: Seek lo sensitivity: Seek sensitivity Selectivity: Signal-to-Noise Ratio: Harmonic distortion at 1 kHz: Separation: Frequency Response: AM Tuning Range: Seek lo sensitivity Seek sensitivity: Intermediate Frequency: Signal-to-Noise Ratio: Frequency Response: 87. 5 - 107. 9 MHz 10. 7 MHz 13 dBf 51 dBf 31 dBf 80 dB at 400kHz 65 dB (stereo), 70 dB (mono) 0. 7% (stereo), 0. 5% (mono) 30 dB 30-15, 000 Hz ± 3 dB 530 - 1, 710 kHz 50 dBµV 25 dBµV 450 kHz 50 dB 30-5, 000 Hz + 3dB Audio Speaker Impedance: Maximum Amp Power: RMS Power: Bass Control: Treble Control: Loud: Preamp Output: 4-8 ohms 4 X 15 Watts (at 4 ohms) 4 X 5. 5 Watts (at 4 ohms) <1% THD ± 10 dB @ 100 Hz ± 10 dB @ 10 kHz + 8 dB @ 60 Hz & + 2 dB @ 8 kHz 2-Channel, Low-Impendance (100 ) Preamplifier Over 3 Volts of Distortion-Free Preamp Output CD Player Cassette Signal-to-Noise Ratio: Tape Wow and Flutter: Tape Frequency Response: 55 dB 0. 10% dB 30-18, 000 Hz + 3 dB 180 x 52 x 155 mm, 7 x 3 x 6 1/8 in. 1. 4 kg (3. 0 lb. ) 12 V DC car battery (11-16 V DC allowable) 15°F to 120°F, ­10°C to 50°C · Unit · Faceplate · Wire Harness, including 2-channel RCA Preamp Output · DIN Sleeve · Mounting Hardware · Owner's Manual in English, French, Spanish and Portuguese General Dimensions (w/o projecting parts/controls): Mass: Power Requirement (neg. grnd. ): Operating Temperature: Supplied Accessories: Design and specifications subject to change without notice. 11 Location of Controls 1. Display Instructions -- General Operation See Traffic Safety & Precautions on page 4. "Press" means a momentary press of less than 1/2 second. [. . . ] In any FM Bank, press SCA/TS for 2 seconds to activate FM Travel Store. (In AM Bank, press it for 2 seconds to activate AM Travel Store. ) TS appears. Beginning at the bottom of the band, TS stores five relatively strong stations, one on each of the five preset buttons, and returns to preset 1. Pressing any tuning-related button during Travel Store process cancels search operation. [. . . ]