User manual BLAUPUNKT MANHATTAN CD148

[. . . ] osch Group FCC Warnina The equipment has been tested and found to comply with the limits for a Class B device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with instructions, may cause harmful interference with radio communications. However, there is no guarantee that radio interference will not occur in particular installation. [. . . ] Make sure the unit is firmly anchored (preferably at both front and back) and does not vibrate. Mounting Hardware 00 @ 0 Sleeve Mounting Strap and Screw @ w 9 (2) (3) Release Keys Mounting The Unit in Most Dashboards 1 Install the Sleeve (1) in the dashboard. 2 Select and bend the appropriate tabs to hold the sleeve firmly in place. Attach the Mounting Strap (2) to the underside of the dashboard, using screw. Attach the back of the unit to the mounting strap using the support stem bolt and hardware. Bend these tabs v 8 Mounting the Unit in a Japanese Car . You may have difficulty mounting this unit in some Japanese cars that have IS0 mounting features (side-bracket mounting systems). 1 Run a blade along the slits on the back of the front trim ring, unscrew the two side screws, and separate it from the unit. Save the trim ring and related hardware in case you ever want to install the unit in another vehicle. 2 Use the vehicle's own mounting hardware to attach the unit. 1 Slit 2 TOYOTA max. size M5x8 to dashboard/center console Bracket support I I 2 NISSAN max. to dashboard/center console Bracket support d 9 Maintenance Removing the Unit Use the Release Keys as shown below. Keep them in a safe place in case you need them in the future. Fuse Replacement When replacing the fuse, be sure to use one with the correct amperage, which will be stated on the fuse case. Never use a fuse that has a stated amperage exceeding the one supplied for this unit, as this could cause malfunction and serious damage to the unit. 10 Specifications Audio Power Specifications Power Output and Total Harmonic Distortion: 13. 5 watts per channel minimum continuous average output into 4 ohms, 4 channels driven, from 30-15, 000 Hz with no more than 1% total harmonic distortion. Other Specifications Tuner FM Tuning Range: Intermediate Frequency: FM Mono Sensitivity: Seek lo sensitivity: Seek sensitivity Selectivity: Signal-to-Noise Ratio: Harmonic distortion at 1 kHz: Separation: Frequency Response: 87. 5 - 107. 9 MHz 10. 7 MHz 13 dBf 51 dBf 31 dBf 80 dB at 400kHz 65 dB (stereo), 70 dB (mono) 0. 7% (stereo), 0. 5% (mono) 30 dB 30-l 5, 000 Hz k 3 dB 530 - 1, 710 kHz 50 dBuV 25 dBuV 450 kHz 50 dB 305, 000 Hz f 3dB 4-8 ohms 4 X 35 Watts (at 4 ohms) 4 X 13. 5 Watts (at 4 ohms) ~1% THD + 10 dB @ 100 Hz f 10dB @ 10 kHz + 8 dB @ 60 Hz & + 2 dB @ 8 kHz 4-Channel, Low-lmpendance (100 Q) Preamplifier Over 3 Volts of Distortion-Free Preamp Output 90 dB 90 dB 5-20, 000 Hz + 3 dB . Ol% 180x52x155mm, 7x3x6'/~in. 1. 4 kg (3. 0 lb. ) 12 V DC car battery (11-16 V DC allowable) 15°F to 12O"F, -10°C to 50°C Unit Faceplate Wire Harness, including 2-Channel RCA Preamp Output Harness DIN Sleeve Mounting Hardware Owner's Manual in English, French, Spanish and Portuguese 4-Channel Preamp Output Harness (Part No. 8634494218) (Available at l-800-920-21 21) l l l l l l l AM Tuning Range: Seek lo sensitivity Seek sensitivity: Intermediate Frequency: Signal-to-Noise Ratio: Frequency Response: Audio Speaker Impedance: Maximum Amp Power: RMS Power: Bass Control: Treble Control: Loud: Preamp Output: CD Player Signal-to-Noise Ratio: Dynamic Range: Frequency Response: Harmonic Distortion: General Dimensions (w/o projecting parts/controls): Mass: Power Requirement (neg. grnd. ): Operating Temperature: Supplied Accessories: Optional Accessories: Design and specifications subject to change without notice. 10. REL (Release) Button PWR (Power) Button Source (and Radio Band) Select Mute/Audio Button SCA (Scan) TS (Travel Store) LD (Loudness)/ SENS (Tuning Sensitivity) CLK/Display Change Disc Insertion Slot CD Eject + Button Volume + Bass + Treble + ' Balance Left Fade to Front 11. A Button Seek and Manual Tuning Track Up Audible CD Cue Clock Hours 13. V Button Seek and Manual Tuning Track Down Audible CD Review Clock Minutes 14. Display Instructions - General Operation See Traffic Safety & Precautions on page 4. "Time Out" When additional button presses are anticipated to complete a procedure, the unit will automatically exit the procedure after 4 seconds of inactivity. 12 . Ignition-Off Clock Recall Any button press while ignition off displays time for about 8 seconds. Ignition-On Unit lights up and clock is displayed. If power was not switched off before face removed, unit will automatically power-on when face is reattached. Power (PWR) On/Off When ignition on, press PWR or. insert a disc to turn unit on. [. . . ] Pressing any tuning-related button during Travel Store process cancels search operation. Frequency blinks (along with preset number if appropriate) during scanning. Unit continuously scans until user stops scan by pressing SCA, , another tuning button or SRC. . Compact Disc Play Operation CD Insertion Make sure that "CD IN" isn't lit. In rare instances when a disc has more than 28 tracks, it may take up to about a minute for the unit to read the disc and for playback to start. [. . . ]