User manual BLAUPUNKT MADRID RCM 148

[. . . ] Radio / Cassette / Changer Como RCM 148 Madrid RCM 148 Texas RCM 148 Madison DJ New Orleans DJ Operating instructions 18 17 16 15 14 13 12 11 Madrid RCM 148 New Orleans DJ 1 10 Como RCM 148 Madison DJ Texas RCM 148 2 4 5 6 7 8 9 11 2 3 4 Fernbedienung RC 06 (Option) Remote control RC 06 (optional) Télécommande RC 06 (en option) Telecomando RC 06 (optional) Afstandsbediening RC 06 (Optie) Fjärrkontroll RC 06 (Tillval) Mando a distancia RC 06 (opcional) Telecomando RC 06 (opção) 2 Contents Quick reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Scrolling through the broadcasting networks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Automatically storing the strongest stations with Travelstore . . . . . . . . . . . . . . . . . . . . . . . 40 Scanning stored stations with Preset Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · Press the FMT or BND button as many times until the desired memory bank lights up in the display. Notice: Should you tune in a station which has already been stored before, then the corresponding preset position and memory bank will briefly flash in the display. Recalling stored stations You can recall any stored station at the touch of a button. · Press the corresponding preset button briefly to recall the station. Automatically storing the strongest stations with Travelstore You can automatically store the six most powerful FM stations of your current reception area sorted according to their signal strength. The six strongest FM stations will be automatically stored on the memory bank "T" (Travelstore). When this process has been completed, the radio will play the first station stored on preset 1. If desired, stations can also be stored manually on the Travelstore bank (see "Storing stations"). Storing stations On FM, you can store six stations on the preset buttons 1-6 for each of the memory banks I, II and T. (only with Como RCM 148, Texas RCM 148, Madison DJ) · Select the desired memory bank. · Tune in a station with the rocker switch (either automatically / or manually << >>). Scanning stored stations with Preset Scan You can have all of the stored stations briefly scanned on all wavebands. Preset Scan cannot be started unless PTY has been switched off ("PTY" is not lit up in the display). All of the stored stations to be received will be scanned one after the other. To select a scanned station and switch off Preset Scan: · Press SC briefly. Note: If "TA" shows on the display panel, the system will scan the stored traffic stations only. · Press and hold down the desired preset button until the radio resumes play after the muting (takes approximately 1 sec. , confirmed by beep). The activated preset button is indicated in the display. 40 Scanning stations with RadioScan You can briefly scan through all of the receivable stations of the selected waveband. During the actual scanning process "FM SCAN" or "AM SCAN" will be displayed. To select a scanned station and switch off Radio-Scan: · Press SC briefly. If no station is selected, the scan function will be automatically switched off after the frequency band has been run through completely. The unit will tune in the station listened to before starting the scan. Switching from stereo to mono Every time the radio is switched on, stereo playback is activated automatically. You can also switch between mono and stereo reception manually: / lo button for approxi· Press the mately 1 sec. The selected condition will briefly appear in the display. Switching PTY on/off · Press PTY. When the function is active, the programme type selected last will briefly appear in the display. "PTY" will be permanently indicated in the lower right corner of the display panel. Programme type Loudness Adjusts the low bass frequencies for a more natural sound. Switching Loudness on/off: · Press the AUD button for approximately 1 sec. When the Loudness function is active, "LD" will light up in the display. [. . . ] The display will show you the adjusted condition. MIX For changer operation only. The next disc is again selected at random. BLS ON ­ Automatic fast tape forwarding if the system senses an unrecorded tape portion continuing for more than 15 seconds. BLS OFF ­ The function is deactivated. ITALIANO DSC (Direct Software Control) allows you to customise certain programmable, basic settings to suit your personal needs and preferences and then store them. In the following you can find an overview of these settings, so that you can always reset to these if desired. [. . . ]