User manual BLAUPUNKT KEY WEST CD169

[. . . ] KEY WEST CD169 High-Power FM/AM/CD Receiver with Detachable Face AT TS 168 W TS E KEY W PWR OPEN ST CD 169 VOL XBASS MIX SC/PS RPT AUD Robert Bosch Corporation Sales Group -- Blaupunkt Division 2800 South 25th Avenue, Broadview, Illinois 60153 288E8741 Bosch Group M UT NS SE E K N/TR TU FCC WARNING This equipment has been tested and found to comply with the limits for a Class B device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with instructions, may cause harmful interference with radio communications. However, there is no guarantee that radio interference will not occur in particular installation. [. . . ] The unit will stop at each preset station for 8 seconds, before continuing to the next preset station. Press the SC/PS again to stop Preset Scan Tuning and remain this on the selected frequency. Local/Distant (LO/DX) Selection This feature is used to select the strength of the signals at which the radio will stop during Seek Tuning. Press the MUTE / SENS for more than 2 seconds to select the Local setting and only strong (local) stations will be received. Pressing again will select the Distant setting and the radio will stop at a wider range of signals, including weaker more distant stations. Press the Memorizing Stations Automatically (Travel Store) to select the desired AM or FM band. BND / TS TUN/ TRK or TUN/ TRK for more than 0. 5 second to activate the manual tuning mode. After 4 seconds of completing Manual Tuning, the tuning control will revert to the Seek Tuning mode. 1. 2. Press the BND / TS to select the desired band. Hold the BND / TS pressed for longer than 2 seconds. Up to 6 stations with strong signals will be automatically stored in preset memory for the selected band. Note This function is available for FT and AT. Scan Tuning 1. Hold the Memorizing Only the Desired Stations to select the desired band. You can store up to 6 stations on each band (18 for FM 1, FM 2 and FT, 12 for AM and AT) in the order of your choice. BND / TS SC/PS pressed for less than 2 seconds. Press the SC/PS again to stop Scan Tuning and remain this on the selected frequency. Tip While tuning, the pie-shaped signal-strength meter on the display is lit differently depending on the strength of the signal. to tune in stations. TUN/ TRK Press and hold the desired preset memory button 1 6 for about 2 seconds until the frequency indicator flashes twice. The number of the pressed preset memory button appears on the display window. Note If when you store another station on the same preset number button, the previously stored station is replaced with new one. E-4 Storing the station names You can assign a name to each radio station and store it in memory. As many as 30 station names can be stored, composed with 8 characters each. Direct Access to Memorized Stations via Station Call You can search for the memorized AM & FM station names in the memory. Level Meter Sensitivity selection The sensitivity of the level meter display can be switched. You can select : · LEVEL 1 : Normal sensitivity · LEVEL 2 : High sensitivity Storing the station names 1. " appears on the display window. XBASS 2. Rotate the dial to select the desired meter indication. METER 1 § METER 2 § METER 3 § METER 4 § METER 0 Erasing the station names Tune in any station and press the seconds. DISP Each time you press , the current mode appears on for more than 2 the display window and then the mode change as follows: XBASS 0 § XBASS 1 § XBASS 2 § XBASS 3 § XBASS 4 Press the MUTE / SENS . Rotate the dial to select the name of the station that you want to erase. To return to the normal radio reception, Press DISP L-ch Level meter R-ch Level meter . E-5 CD Operations Playing the CD player Loading Discs Listening to a disc that is already loaded Press the CD to select the CD mode. [. . . ] · This unit is designed for negative ground 12 V DC operation only. You can not use it for 24 V or other types of car batteries. 1 2 3 4 5 6 7 8 9 Make sure the car's ignition key has been removed. Connect the wiring harness wires in the following order : GND (Black), BTT (Yellow), ACC (Red) and ANTENNA REMOTE (Blue), and tape each so they do not come in contact with each other. Connect the car's antenna terminal to the antenna socket of the unit. [. . . ]