User manual BLAUPUNKT GTA 2100

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual BLAUPUNKT GTA 2100. We hope that this BLAUPUNKT GTA 2100 user guide will be useful to you.


BLAUPUNKT GTA 2100 : Download the complete user guide (241 Ko)

You may also download the following manuals related to this product:

   BLAUPUNKT GTA 2100 (198 ko)
   BLAUPUNKT GTA 2100 (241 ko)
   BLAUPUNKT GTA 2100 annexe 1 (241 ko)
   BLAUPUNKT GTA 2100 annexe 1 (241 ko)

Manual abstract: user guide BLAUPUNKT GTA 2100

Detailed instructions for use are in the User's Guide.

[. . . ] Recommendation: A power amplifier's performance is only as good as its installation. Proper installation will maximise the overall performance of your audio system. Should you decide to install the amplifier yourself, however, please read through these instructions carefully, and take your time over the installation. [. . . ] The crosssection of the positive and negative cable must be at least 6 mm2. gTA 2100 amplifier The amplifier is suitable for connection to car radios with Cinch connector. Use the Blaupunkt ISO Cinch adapter to connect the amplifier to car radios with ISO connector. Clean the contact surface of the ground point down to bare metal and coat with antiseize graphite petroleum. Integral fuses The integral fuses within the amplifier protect the final stage and the entire electrical system in the event of a fault. This enables the amplifier to be switched on and off with the radio's On/ Off switch. Gain control The gain control enables the input sensitivity of the final stage to be matched to the output voltage of your car radio preamp output. Adjust the input sensitivity in accordance with the manufacturer's specifications when connecting the amplifier to other radios. important: Turning the gain control clockwise increases the input sensitivity of the amplifier , and thereby also the volume. The gain control is however not a volume control; an increase in volume is not achieved in the maximum position, even if this subjectively appears to be the case. The system merely increases the volume more quickly when the volume is turned up on the radio. Tri-mode loudspeaker connections GTA amplifiers can be used in a combined mono/stereo mode (Fig. This facility enables the amplifier to be used simultaneously with stereo satellite speakers (mid-range and tweeter) and a mono subwoofer. The connections are somewhat more complicated in this case, as they require the use of passive crossover networks (not supplied with the amplifier) which divide the frequency ranges between the various loudspeakers. If you do not wish to purchase and connect the components separately, a number of ready-assembled tri-mode crossover networks are available. CAUTION: In tri-mode (combined mono/stereo mode) the amplifier must be presented with a load of at least 2 Ohms (stereo satellite speakers) or 4 Ohms (mono subwoofers). Lower loads cause overheating of the amplifier and may damage it permanently. loudspeaker connections (If the amplifier is to be connected in a bridged mode , proceed with the section "Bridged loudspeaker connections". [. . . ] run a standard commercial positive cable to the battery and connect to the fuse holder. Use cable grommets when passing cables through holes with sharp edges. Bolt a standard commercial negative cable to a ground point free of induced noise (car body bolt, body panel) - not to the neg3 This information is subject to change without notice! [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE BLAUPUNKT GTA 2100




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual BLAUPUNKT GTA 2100 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.