User manual BLAUPUNKT CALGARY CD30 US

[. . . ] CD changers The following CD changers can be connected directly: CDC A 06, CDC A 08, CDC A 072 and IDC A 09. The CDC A 05 and CDC A 071 can be connected with an adapter cable (Blaupunkt no. 7 607 889 093). Traffic safety Traffic safety is always the top priority. Do not operate your car audio system unless the traffic conditions permit. [. . . ] A CD inserted into the car audio system will remain in place. Replacing the operating panel Slide the operating panel into the guides from left to right. Press the left-hand side of the panel onto the car audio system until it locks into place. Press 1. The release panel will unlock. Note: While replacing the panel, be careful not to press on the display. 7 PORTUGUÊS ESPAÑOL SVENSKA NEDERLANDS ITALIANO FRANÇAIS ENGLISH SWITCHING ON/OFF Switching the car audio system on/off The car audio system can be switched on/off in a number of ways. If the car audio system has been connected to your vehicle ignition, it is possible to switch it on and off with the ignition. You can also switch the car audio system on when the ignition is switched off. VOLUME CONTROL Volume control The car audio system volume can be adjusted to levels from 0 (off) to 66 (maximum). To increase the volume, turn the volume control knob 3 to the right. To decrease the volume, turn the volume control knob 3 to the left. Adjusting the power-on volume It is possible to adjust the volume at which the car audio system switches on. Press down and hold 4 until the car audio system switches on. Note: To prevent the car battery from running down, the radio will switch off again automatically after one hour. Press MENU <. To make it easier to select the desired volume, you will be able to hear any changes made while you are adjusting the volume. If you adjust this setting to 0, the car audio system will switch on at the volume used before it was switched off. Press Switching the car audio system on/ off with the removable front panel Remove the release panel. The car audio system will switch off. Replace the release panel. The car audio system will switch on again. Switching the car audio system on/ off by pressing 4. Press 4 to switch the car audio system on. Press 4 for longer than 2 seconds to switch the car audio system off again. Warning of serious injury When the power-on volume is set to the maximum level, it may be extremely loud when the car audio system is switched on. When the power-on volume is set to 0 and the car audio system was played at maximum volume before it was switched off, it may be extremely loud when the car audio system is switched back on. This could result in serious injury to your ears. 8 VOLUME CONTROL desired settings, press MENU <. ENGLISH PORTUGUÊS ESPAÑOL SVENSKA NEDERLANDS ITALIANO FRANÇAIS ENGLISH Once you have selected the Mute You can reduce the volume of the car audio system immediately (mute). How to the confirmation tone switch on/off If you hold down a key for longer than two seconds, e. g. in order to save a station on one of the station keys, a confirmation tone will sound (beep). This beep is adjustable: Press 4. Selecting the mute level It is possible to select the mute level. Press the MENU key <. So-called "CD singles" with a diameter of 8 cm and contoured CDs ("shape CDs") are not suitable for playback in this unit. Normal playback is then continued. Pausing playback (PAUSE) Press button 2 ( ) =. "PAUSE" appears in the display. Playback is continued. Changing the display To change the display between track number and playing time: Press the MENU button <. "MENU" appears in the display. Keep pressing the button : until "CD DISP" appears in the display. "TIME" stands for the playing time and "PLAY" for the track number display. Selected the required setting using the or button :. Press the MENU button <. 13 CD CHANGER OPERATION CD changer operation Note: Refer to the instructions included with the CD changer for more information on how to handle CDs, how to insert CDs into the changer and how to operate the changer. Press or : to select the desired setting. Press MENU <. Repeating individual tracks or entire CDs (REPEAT) To repeat the track currently playing, press 3 (RPT) = briefly. "RPT TRCK" will appear briefly in the display, RPT will light up in the display. Starting CD changer operation Press CD·C 8 repeatedly until "CHANGER" appears in the display. Playback will begin with the first CD the changer detects in the magazine. To repeat the entire CD currently playing, press 3 (RPT) = again. "RPT DISC" will appear briefly in the display, RPT will light up in the display. Stopping the REPEAT function Selecting CDs To select a different CD up or down, press or : once or the required number of times. To stop the REPEAT function for the current track or CD, press 3 (RPT) = repeatedly until "RPT OFF" appears in the display and RPT no longer lights up. Selecting tracks To select a different track up or down on the CD currently playing, press or : once or the required number of times. Playing tracks in random order (MIX) To play the tracks of the currently selected CD in random order, press 4 (MIX) = briefly. "MIX CD" will appear briefly in the display, MIX will light up in the display. Switching the display mode To switch the display between the CD number and the elapsed playing time, press MENU <. "MENU" will appear in the display. To play the tracks of all of the CDs in random order, press 4 (MIX) = again. "MIX ALL" will appear briefly in the display, MIX will light up in the display. Press Press : repeatedly until "CDC DISP" appears in the display. [. . . ] Once you have set the time, press MENU <. Selecting the 12/24-hour time display mode Press MENU <. "MENU" will appear in the display. Press : repeatedly until "24 H MODE" or "12 H MODE" appears in the display. Press or : to switch the display mode. Once you have selected the mode, press MENU <. 16 TONE Adjusting the tone Adjusting the bass To adjust the bass, press AUDIO 9. "BASS" will appear in the display. VOLUME DISTRIBUTION (BALANCE/FADER) Adjusting the volume distribution Adjusting the balance To adjust the balance, press GEO ;. "BAL" will appear in the display. ENGLISH Press or : to alter the bass. 9. "BASS" will appear in the display. "TREBLE" will appear in the display. Press or : to alter the treble. "BAL" will appear in the display. Press GEO ; again. "FADER" will appear in the display. Switching Loudness on/off Loudness boosts the bass and treble when the volume is low to create a more natural sound. Press or : to alter the fader for the front and rear speakers. seconds. Adjusting Loudness intensity The Loudness boost can be set in stages from one to six. "LOUDNESS" appears in the display. Press or : to alter the Loudness setting. Once you have completed adjusting the settings, press MENU <. [. . . ]