User manual BLAUPUNKT ARIZONA CM148

[. . . ] 2 Dispiay The display consists of three fields and changes according to the operating mode and function. . "`-*%w:w\ y_. lj i \a, *" Display field 1: Radio mode Memory banks and wavebands Brief indication of preset station (e. g. Pl) Cassette mode CAS - cassette inserted Chanaer mode (Chanaer sold separately) Current track Display field 2: Radio mode Radio frequency or station name Clock display Cassette mode TAPEl/TAPE2 - side of tape being played. Clock display Chanaer mode (Chanaer sold seoaratelv) Display field 3: Displays active functions. - Stereo - Cassette inserted Disc - CD changer connected E - Loudness CT, Radio mode lo - Seek tuning sensitivity Chanaer mode (Changer sold separately) RPT - Repeat function MIX - Tracks played at random Numeric and graphic representation of the volume and audio settings. CD number being played by changer. [. . . ] CD playback starts with the first CD identified by the changer. >> Up: Press briefly. (When at start of first track, unit goes to last track on same disc. ) REVIEW - fast reverse (audible): Hold button down. Selecting a CD When CD playback starts, all active CD functions and the CD number will light up in the display. To change the display between CD number and elapsed time, press 0 during CD playback. << Press the button repeatedly to skip several tracks. The number of the selected track will appear beside "T" (track). CLOCK/Display changes SCAN Use this function to scan all of the CD tracks. To start the Scan function: l Hold down SCA until "SCAN" appears. All of the CD tracks will be scanned one after the other in ascending order. The SCAN function will also be cancelled by pressing any other button, except for the volume controls and the AUD and ON buttons. l Switch REPEAT-T on: Press WRPT briefly. This unit is equipped with an internal clock. Disolay priority until To alter the display priority, press you hear a beep. Temporary display chanae Press ' briefly as many times as needed to show the desired information for a few seconds. Radio mode Press to switch between the clock, the station name and the frequency. Cassette mode Press 1 to switch between the track played and the clock. Changer mode (optional) P r e s s to switch the display of the CD number, the playback time elapsed and the clock. Switch REPEAT-D on: l Hold 4/RPT down until a beep is emitted. MIX You can have the CD tracks played in random order. The following options are possible: - Mix all tracks of one CD ("MIX-CD") or - RPT CD tracks can be played repeatedly. The following options are possible: - Repeat the current track ("REPEAT-T") or Repeat the CD, i. e. "RPT" will appear in display field 3 as long as RPT is active. "REPEAT-T" lights up briefly in display field 2 when you activate this function and each time the track changes. - Mix all tracks of all CDs ("MIX-ALL") in manner determined by the CD changer model. "MIX" will appear in display field 3 as long as the MIX function is active. "MIX-CD" lights up briefly in display field 2 when you activate this function and each time the track changes. Switch MIX-ALL on: Hold 5/MIX down until a beep is emitted. l 15 Turn On Message Setting the clock l DSC programming The car radio has been equipped with DSC (Direct Software Control) to allow you to customize certain programmable, basic settings to suit your personal needs and preferences and then store them. In the following you can find an overview of these settings, so that you can always reset to them if desired. l Set the clock in the DSC mode. Press DSC again to exit DSC mode. l This unit offers you the possibility to enter a turn on message of up to 40 characters. The message will briefly appear in the display each time you turn the unit on. [. . . ] Avoid mounting locations where the receiver would be subject to high temperatures, such as from direct sunlight or hot air from the heater, or where it would subject to dust, dirt or excessive vibration. The illustration below shows a typical installation, however, you may need to adjust the installation, depending on the receiver. If you have questions or need additional installation hardware, consult your Blaupunkt dealer. Make sure the receiver is firmly anchored (preferably at both front and back) and does not vibrate. Installing the Receiver in Most Dashboards This car receiver and its mounting bracket are designed for installation in vehicles with a standard DIN installation compartment measuring 182 x 53 mm, a 165 mm installation depth and an instrument panel thickness of approximately 1 to 20 mm in. [. . . ]