User manual BLAUPUNKT ACS2500

[. . . ] To switch between the FM memory banks: Toggle button until the desired bank is indicated in the display. To automatically store the six most powerful stations with Travelstore: To store: Press the FM·T button until the seek tuning process begins and is indicated in the display. To recall: Toggle the FM·T button until the display shows "T". Then briefly press one of the preset buttons 1-6. Use the buttons to alter the selected setting. [. . . ] Always make sure that you are still able to hear any warning signals coming from outside of the vehicle, such as police or fire engine sirens, so that you can react accordingly. Therefore, you should always select a moderate volume for playing your car radio while you are driving. Entry of a wrong code number It should not be possible for a thief to find out the correct code number by trial and error. This is why the set will be blocked for a certain period of time after a wrong code number has been entered. After the first three unsuccessful attempts the system will lock for 10 seconds; after further attempts, the waiting time extends to one hour. Note: Keep your car radio passport with the code number in a safe place in order to avoid Installation/Connection If you would like to install this equipment yourself or add any new components, please carefully read the installation and connection instructions following the appendix. Use only the accessory and replacement parts approved by Blaupunkt. QuickOut This unit is available with or without the "QuickOut" (quick release) option. The QuickOut handle facilitates removal of 16 "unauthorised access" to your car radio. When the security code system is activated, the unique code must be entered each time the power to the unit was interrupted. The radio will function again as soon as you have entered the correct code. If you have lost your radio passport and forgotten the code number, your radio can only be made operable again by one of our authorised service workshops, which is subject to payment. - Press the TA button twice; the display shows "2520". Switching off security coding · · · · Turn off the radio. Press AF and > buttons simultaneously and hold down while switching the set on again. If you are tuned into a regional programme and wish to continue listening to this programme, · press the AF button for approximately 2 seconds. If you leave the service area of the regional programme tuned into, or if you would like to take advantage of the full RDS service, switch to "REG OFF". AF - Alternative frequency The AF (Alternative Frequency) function makes sure that the strongest frequency of the currently selected programme is always tuned in automatically. This function is activated when "AF" appears in the display. In order to switch this function on or off, · press the AF button briefly. The radio will switch to mute briefly while searching for the strongest reception signal. If "SEARCH" appears in the display when 18 Selecting a station Using the buttons there are several different ways of tuning into a station: Automatic tuning Prerequisite: "AF" and "m" do not light up in the display, i. e. the Alternative Frequency function and manual tuning are switched off. Use the AF and lo·m buttons (lo, m, -, lo) to adjust the respective modes. ; the car radio will automati· Press cally search for the next station. or the button deWhen keeping the pressed, seek tuning will speed up in upwards or downwards direction. ; the frequency will change in · Press short intervals in upwards or downwards direction. or button down, the When holding the frequency scan is speeded up. Switching from stereo to mono (FM) If reception is poor, you may get better sound quality by switching to mono: · Press the lo·m button until a beep sound is released and the stereo sign disappears from the display. [. . . ] Toggle FM·T until the desired memory bank is indicated in the display · Toggle the corresponding preset button until the desired preset station appears in the display. Traffic announcement priority on/off If the priority for traffic announcement programmes is activated, "TA" will light up in the display. 20 Automatic seek tuning start Prerequisite: The priority for traffic announcements has been activated. When leaving the reception area of the tuned in traffic programme station while listening to a tape or after having turned down the volume completely, the system will automatically start searching for a new TA programme. If no such station is found within approximately 30 seconds, tape operation will be stopped and a warning beep will sound. [. . . ]