User manual BIZFON 7000 INSTALLATION GUIDE

[. . . ] Power ­ Indicates system start up activity Drive ­ Indicates drive activity Alert ­ Indicates drive or other system fault condition RJ-45 10BaseT/100BaseTX Auto-Sensing Auto-MDI/MDIX switched Local Area Network Ethernet ports. Safe Mode Reset Button RJ-45 10BaseT/100BaseTX Auto-Sensing Auto-MDI/MDIX Wide Area Network port. RJ-11 Power Fail analog phone connector RJ-11 dedicated loop-start FXO ports for central office connection (Ports 1-3) RJ-11 loop-start FXO for central office connection or FXS universal telephone auto-sensing ports for analog extension connection (Ports 4-9) RJ-11 FXS ports for analog or fax extension (Ports 10-16) 3. 5 mm stereo audio mini jacks for music-on-hold and overhead paging 3 4 5 6 7 8 9 10 50 Stiles Road · Salem, NH 03079 · Toll Free 1-800-260-5793 · 603-870-9400 · www. Bizfon. com © 2005 All rights reserved. All other names may be trademarks or registered trademarks of their respective owners. [. . . ] Use the Bizfon 7000 System Administration Guide to supplement the information on the web pages when necessary. If the server has been previously configured for another installation, you should restore it to its factory default configuration. Format the disk and perform a Software Update. 50 Stiles Road · Salem, NH 03079 · Toll Free 1-800-260-5793 · 603-870-9400 · www. Bizfon. com © 2005 All rights reserved. All other names may be trademarks or registered trademarks of their respective owners. Revised: August 5, 2005 Page 10 Installation Instructions 9 Data Network The Local Area Network (LAN) and Wide Area Network (WAN) data network ports are 10BaseT/100BaseTX auto-sensing and auto-MDI/MDIX ports. The Bizfon 7000 is a sophisticated network appliance that must be properly configured before being connected to the LAN and WAN. Note: Do not plug any network cables into the server without first properly configuring the server. Failure to heed this warning may result in a disruption of network connectivity with other equipment on the network. After the network is properly configured, the LAN and WAN network cables can be plugged in. The four LAN ports are all switched Ethernet ports and may be used in any order. LED Identification Left - Amber Right - Green State On Off Off On Blinking Description 100Mbps 10Mbps No link: the network is not connected Link: the network is successfully connected Activity: data is being transmitted or received Table 4: Network Port LED Definitions 50 Stiles Road · Salem, NH 03079 · Toll Free 1-800-260-5793 · 603-870-9400 · www. Bizfon. com © 2005 All rights reserved. All other names may be trademarks or registered trademarks of their respective owners. Revised: August 5, 2005 Page 11 Installation Instructions 10 Configuration Example "Unlimited" number of SIP phones SIP Phone SIP Phone SIP Phone Network Device 10/100 E-net 10/100 E-net 10/100 E-net E-net Switch or Hub E-net Switch or Hub Bizfon 7000 Server 10/100 E-net 10/100 E-net 10/100 E-net LAN WAN 10/100 E-net Network Printer Network Server Music on Hold Source Paging Amplifier Analog Phone Analog Phone Analog Phone FAX Machine 10/100 E-net DSL or Cable Modem 10/100 E-net Line level audio input In Out RJ-11 Up to 13 outside DID lines* Line level audio output Up to 13 inside extensions* PSTN Central Office Up to 9 outside FXO lines* * Maximum of 16 analog connections 50 Stiles Road · Salem, NH 03079 · Toll Free 1-800-260-5793 · 603-870-9400 · www. Bizfon. com © 2005 All rights reserved. All other names may be trademarks or registered trademarks of their respective owners. Revised: August 5, 2005 Page 12 Installation Instructions 11 Physical and Environmental Specifications Dimensions (W x H x D) Weight (Base Model) Power Temperature Humidity 17. 5 x 15 x 3. 5 inches (44. 5 x 38 x 9 cm) 17 lbs AC 100-127/200-240V, 4/2A, 47-63Hz 0° ~ 40° C 15% ~ 90% RH, Non-condensing 50 Stiles Road · Salem, NH 03079 · Toll Free 1-800-260-5793 · 603-870-9400 · www. Bizfon. com © 2005 All rights reserved. All other names may be trademarks or registered trademarks of their respective owners. Revised: August 5, 2005 Page 13 Installation Instructions 12 Regulatory Notices 12. 1 FCC Part 68 This equipment complies with Part 68 of FCC rules and the requirements adopted by ACTA. On the back side of this equipment is a label that contains, among other information, a product identifier in the format US: AAAEQ##TXXXX. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5. 0). [. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · · · · Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. You may also find helpful the following booklet, prepared by the FCC: "How to Identify and Resolve Radio-TV Interference Problems. " This booklet is available from the U. S. [. . . ]