User manual BISSELL SPOTBOT 88D6

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual BISSELL SPOTBOT 88D6. We hope that this BISSELL SPOTBOT 88D6 user guide will be useful to you.


BISSELL SPOTBOT 88D6 : Download the complete user guide (712 Ko)

Manual abstract: user guide BISSELL SPOTBOT 88D6

Detailed instructions for use are in the User's Guide.

[. . . ] NonbISSEll cleaning formulas may harm the machine and void the warranty. www. bissell. com 5 Special features Front view Clean/solution tank Located to the right of the unit when you are facing the unit. Automatic Smart System control paneI Located in the center of the unit. This is where you will begin selection of the smart cleaning cycle you would like to use (detailed instructions on page 8). Dirty/collection tank Located to the left of the unit when you are facing the unit. [. . . ] Status Indicators Much like the dishwasher in your kitchen, the status Indicators will instruct you regarding status within a cleaning cycle. You will hear changes in the sound of the machine at different points in a cycle. When your selected cleaning cycle is complete, the finish light will illuminate and you will hear a beep every five seconds until you depress the stop button. 5. 6. 8 www. bissell. com Operation Handsfree cleaning 1. 2. Place the unit directly over the spot or stain, making sure the stain is in the center of the handsfree cleaning area. Select which cleaning cycle (surface stain or set-in stain) you would like to begin with. Your SpotBot will begin spraying, brushing and suctioning up the spots and stains in its pre-programmed cycle. Both cycles have been tested and proven to deliver superior cleaning results, taking the guesswork out of cleaning for you. When the cleaning cycle you have selected is complete, the SpotBot will beep. The beep will continue every five seconds until you depress the stop button. If you have used Oxy GEN2, this chemical will continue to work for the next six to eight hours, cleaning your spots and stains all the way to the backing of the carpet. 3. Tip: If the unit accidentally tips or is tilted, the handsfree cleaning brushes will stop. 4. 5. Tip: Some difficult stains may require that you run the cleaning cycle a second time. www. bissell. com 9 Operation Manual/hose cleaning 1. Remove the Tough Stain Brush from the back of the unit by depressing the release button. Select the manual/hose button on the control panel to start the SpotBot. NOTE: In manual mode, the Spotbot will not turn on until the hose is removed from the unit. If it is not removed within 30 seconds of pushing the start button, the unit will shut off. 1 3. 2a 2b 4. If your unit has a built in heater (not standard on all models) press the heater button to turn on the heat feature. Begin cleaning by holding the tool no more than six inches above the soiled surface. Depress the spray trigger for about five seconds to apply the cleaning solution to the soiled area then release the spray trigger. Using the brush on the tool, gently scrub the soiled area for about 30 seconds or until the soiled area appears to be clean. To suction up the dirt and cleaning solution, position the suction nozzle over the cleaned area, apply downward pressure on the tool, and pull nozzle toward you. Normally, this step will require no more than one minute of back and forth passes. NOTE: In manual mode, the Spotbot is equipped with a safety feature which will shut the unit off after 30 minutes. 6. Tip: one of the effective stain removing ingredients in oxy GEN2 is hydrogen Peroxide. Certain people may be affected by the formula when it comes into contact with their skin; it may turn the skin white and/or cause tingling. Washing your hands after use and applying hand lotion will remove any possible white discoloration. 7. [. . . ] The Boat Yard 105 Straight Road old Windsor Berkshire, SL4 2SE United Kingdom Telephone: 0844-888-6644 For New Zealand inquiries: monday - friday 9 am -- 5 pm Parex Industries ltd. 5 Tolich Place henderson 0610 Auckland New Zealand Telephone: 0800-247-735 For Australian inquiries: monday - friday 9 am -- 5 pm bISSEll AUSTRAlIA PTY lIMITED 42 Rocco Dr. Scoresby 3179 Victoria Australia Telephone: 1-800-811-183 For all other inquiries: monday - friday 8 am -- 4 pm bISSEll Homecare, Inc. Po Box 1888 Grand Rapids, michigan 49501 USA Telephone: 01-616-453-4451 fax: 01-616-453-1383 bISSEll HOMECARE INC. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE BISSELL SPOTBOT 88D6




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual BISSELL SPOTBOT 88D6 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.