User manual BISSELL PROHEAT 7950

[. . . ] ProHeat TM SELF PROPELLED USER'S GUIDE 7950 SERIES 3 Safety Instructions 4 Product View/Accessories 5 Assembly 6-17 Features / Operations 17-19 Routine Maintenance 20-21 Troubleshooting 22 Consumer Services 23 Replacement Parts 24 Warranty Thanks for buying a BISSELL ProHeat TM Self Propelled We're glad you purchased a BISSELL ProHeatTM Self Propelled heated formula deep cleaner. Everything we know about floor care went into the design and construction of this complete, high-tech home cleaning system. Your ProHeat Self Propelled is well made, and we back it with a limited 2year warranty. We also stand behind it with a knowledgeable, dedicated Consumer Services department, so, should you ever have a problem, you'll receive fast, considerate assistance. [. . . ] If the area has dried, remove the remaining semi-solids and residue with a sweeper or vacuum. Be sure to pre-test any spot removal solutions or chemicals on an inconspicuous area first. This is extremely important; different dyes and materials could be damaged or discolored by a cleaning solution. If such a change should occur, try a different solution or call a professional. If cleaning on Berber Carpet gently run your machine over a hidden area. If no fuzzing occurs, continue cleaning in soiled area. Use one of the following methods to Preclean the stain: Using BISSELL Tough Stain PrecleanerTM, generously spray the area with the formula. Gently work the solution with a clean cloth or towel into the area using light strokes from the edges of the stain to the center. When you reach the center of the stain with your cloth, gently pinch it in an upward motion. Make sure to turn and change your cloth frequently and do not rub the stain. You may repeat this process several times. 5. or Use your BISSELL deep cleaner as a Precleaner. With one of the tools attached to hose, set the Ready Tools Dial to Pretreat and the SmartMix Dial to the High Traffic setting. Spray the area with solution and allow the Deep Cleaning formula to penetrate for 3-5 minutes. 6. 7. Once the Precleaning is complete, use the attached tool to gently scrub the stain with back and forth strokes. Some difficult stains may require a second treatment. 12 TurboBrushTM (Available on select models only) Assembly Unplug cleaner from the outlet before attaching TurboBrush. Attach TurboBrush to the Flex Hose by pressing tool onto the Grip/Trigger until button snaps into hole. Apply downward pressure on the tool and pull towards you while pulling trigger to spray cleaning solution. H US BR N IO CT SU Release the spray trigger and move the switch to the "SUCTION" position. 2. Disconnect the TurboBrush from the Flex Hose by pushing down on the button lock and pulling straight off. A) Move the switch to the "SUCTION" position B) Rinse under running water. D) Replace TurboBrush in its special storage location on the Tool Caddy in back. (available on select models only) 13 ScotchgardTM protector Applicator (Optional) The Scotchgard protector applicator (with formula included) can be used to help retain the carpet cleanliness you achieve with your ProHeat machine. For best results the post cleaning treatment should be applied while the carpet is still wet or damp. It is recommended that the Scotchgard protector is applied every 12 months in all carpeted areas, and after every deep cleaning for high traffic areas such as entryways and stairs. [. . . ] ReadyTool dial not set on tool setting. 4 5 5 Cleaner not picking up solution. Possible Cause 1 Remedies 1 Ready Tools dial may be at the wrong setting for the cleaning job. Nozzle Window may not be properly attached. Set ReadyTools dial to either Tools or PreTreat or Floor Cleaning. Press down firmly on the black oval gasket at the top window to make sure the two tabs on the back of the Nozzle Window are snapped into the mating slots in the main housing. Re-install lid; refer to The Operations section, page 10 Tank-In-Tank must be firmly seated to function; remove and reseat Tank-in-Tank. [. . . ]