User manual BISSELL POWERFORCE TURBO

[. . . ] PowerForceTM Turbo BAGLESS USER'S GUIDE 82H5 SERIES 220-240V 3 Safety Instructions 4 Product View 5-6 Assembly 6-7 Operation 8-12 Maintenance and Care 13-14 Troubleshooting 14 Consumer Services 15 Replacement Parts 16 Warranty ug110-4049_82H5_1008. indd 1 10/14/08 2:39:30 PM Thank you for buying a BISSELL PowerForceTM Turbo Bagless Vacuum We're glad you purchased a BISSELL PowerForce Turbo Bagless Vacuum. Everything we know about floor care went into the design and construction of this powerful, high-tech home vacuuming system. Your BISSELL PowerForce Turbo Bagless is well made, and we back it with a limited one year warranty. We also stand behind it with a knowledgeable, dedicated Consumer Services Department, so, should you ever have a problem, you'll receive fast, considerate assistance. [. . . ] Always place the vacuum cleaner on the floor with the handle in upright position when using tools. Do not place vacuum cleaner close enough to objects to pull them into rotating brush. Power cord When you are done using your BISSELL PowerForce Turbo Bagless, return it to the upright position and store the power cord. Unplug power cord by grasping the plug (NOT the cord) and disconnect from outlet. Clip molded plug to power cord to secure. NOTICE: certain carpets While vacuuming, and low humidity conditions may generate small static discharges. The discharges are entirely harmless and are not associated in any way with the main power supply. www. bissell. com 7 ug110-4049_82H5_1008. indd 7 10/14/08 2:40:13 PM Maintenance and care To maintain maximum cleaning performance from your BISSELL PowerForce Turbo Bagless, perform these simple maintenance steps. Empty the dirt container when the dirt reaches the "Full" line on the side. Check the inner and outer circular filters, and the pre-motor filter at least once a month and clean or replace as needed. Replace the HEPA media post-motor filter every three to six months. Note: More frequent filter cleaning or replacing may be necessary if you are vacuuming new carpet, fine dust, or have allergy concerns. It is located underneath the dirt container and filter cup in the center of the round part of the Lock `n Seal lever. Remove the small, round, pre-motor filter and any debris on top of it. Rinse well under warm water, then air dry thoroughly before replacing. WARNING: Do not operate cleaner with damp or wet filters or without all filters in place. 3. Pre-Motor Filter www. bissell. com 16 9 10/14/08 2:40:31 PM ug110-4049_82H5_1008. indd 9 Maintenance and care Replacing the HEPA media post-motor filter Use only BISSELL Style 12 HEPA filter in your BISSELL PowerForce Turbo Bagless. The HEPA media post-motor filter assists in the filtration process to return clean air to the room. When the filter becomes dirty, open the door, remove the filter and replace. Note: This filter is not washable and must be replaced. HEPA Media Post-Motor Filter 3. Replace the door by inserting the tabs on the left side and snapping the right side into place. WARNING: To reduce the risk of injury from moving parts, turn the power switch OFF and disconnect plug from electrical outlet. Maintaining the TurboBrush The TurboBrush should be checked regularly for clogs or debris wrapping around the brush roll. Reposition top cover, making sure to line up the inside tab at the front with the opening on the cover. Twist collar until opening is at the bottom to lock into place. 10 www. bissell. com ug110-4049_82H5_1008. indd 10 10/14/08 2:40:38 PM Maintenance and care Check rotating floor brush and drive belt You should check your vacuum cleaner's rotating floor brush and drive belt regularly for wear or damage. You should also clean the brush and brush ends of string, hair and carpet fibers. These can wrap around the brush and hamper its ability to effectively clean your carpet. Place handle in low position and turn vacuum cleaner over so bottom side is up. Remove the two screws from the brush cover (as shown) with a Phillips head screwdriver. Clean strings, hair and other debris from rotating floor brush, paying particular attention to brush ends. Clean strings, hair and other debris from motor pulley and drive belt areas. 8. Air Passageway Replace drive belt Use only BISSELL Style 12 replacement belts in your BISSELL PowerForce Turbo Bagless. [. . . ] Check inner and outer circular filter and post-motor filter for correct installation www. bissell. com 13 10/14/08 2:41:00 PM ug110-4049_82H5_1008. indd 13 Troubleshooting Visible dirt escaping from cleaner (continued) Possible causes 3. Dirt container installed incorrectly Filter cup installed incorrectly Remedies 3. Remove dirt container and make sure filter cup is fully attached Other maintenance or service not included in the manual should be performed by an authorized service representative. Thank you for selecting a BISSELL product. Please do not return this product to the store. BISSELL Consumer Services If your BISSELL product should require service: In the UK, Australia or New Zealand, call BISSELL Consumer Services at the numbers below and we will give you the location of a BISSELL Authorized Service Center in your area. For all other countries, contact your local in country distributor for questions, service, or repair. [. . . ]