User manual BISSELL CLEANVIEW HELIX

[. . . ] I f appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, have it repaired at an authorized service center. Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not use with any opening blocked; keep openings free of dust, lint, hair, and anything that may reduce air flow. Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts. gasoline, kerosene, etc. ) or use in the presence of explosive liquids or vapors. [. . . ] Extension wand Use with desired attachment for a longer reach. notICE: will continue to the floor brush rotate while you use your vacuum for above floor cleaning. to prevent carpet damage, do not lean on the vacuum or let the powerfoot tilt forward. CaUtIon: brush continues to rotate the rotating floor Tip: Hair, string and small objects can block the vacuum hose or tools. to reduce the risk of injury from moving parts, always move the cleaner with the carrying handle at the back of the cleaner. always place vacuum cleaner on floor with handle in upright position when using tools. Do not place vacuum cleaner close enough to objects to pull them into rotating brush. www. bissell. ca 1-800-263-2535 7 Operation Power cord storage When you have finished using your bISSEll Cleanview helix, return it to the upright position and store the power cord. Unplug power cord by grasping the polarized plug (NOT the cord) and disconnect from outlet. Clip molded plug to power cord to secure. notICE: While vacuuming, certain carpets and low humidity conditions may generate small static discharges. the discharges are entirely harmless and are not associated in any way with the main power supply. 3. 4. Maintenance and care to maintain maximum cleaning performance, the following maintenance steps must be performed: 1. Empty the dirt container when the dirt reaches the "Full" line on the side. Check the inner and outer circular filters and the pre-motor filter at least once a month and clean or replace as needed. Replace the post-motor filter every six months. note: More frequent filter cleaning or replacing may be necessary if you are vacuuming new carpet, fine dust, or have allergy concerns. follow the instructions on the following pages to perform these simple maintenance steps. 3. to reduce the risk of electric shock, turn power switch off and disconnect polarized plug from electrical outlet before performing maintenance or troubleshooting checks. WaRnInG: Tip: For maximum cleaning performance, check and clean or replace all filters as suggested. 8 www. bissell. ca 1-800-263-2535 Maintenance and care Empty Dirt Container the dirt container needs to be emptied when the dirt reaches the "full" line on the side of the container. Grasp dirt cup portion handle and pull straight out to remove from vacuum. Put the dirt container back in the vacuum and slide the lever to the "Lock" position. note: the dirt container may be washed in warm water with a mild detergent. Make sure it is completely dry before replacing. 2. Full Line Unlock Position Lock Position 3. Cleaning the inner & outer circular filter Use only genuine bISSEll style replacement filters in your bISSEll Cleanview helix. Grasp the filter cup located at the bottom of the dirt container, lift up and out. DO NOT TRy TO PULL CIRCULAR FOAM FILTER OUT OF THE FILTER CUP WHILE IT IS STILL IN THE vACUUM. you should also clean the brush and brush ends of strings, hair, and carpet fibers. these can wrap around the brush and hamper its ability to effectively clean your carpet. Place handle in low position and turn vacuum cleaner over so bottom side is up. Clean strings, hair and other debris from rotating floor brush, paying particular attention to brush ends. [. . . ] Damage or malfunction caused by negligence, abuse, or use not in accordance with the User's Guide is not covered. If your bISSEll product should require service: Call BISSELL Consumer Services at the number listed below or visit the BISSELL website ­ www. bissell. ca to locate a BISSELL Authorized Service Centre in your area. If there are no authorized BISSELL Service Centres in your area, a BISSELL Representative at canada. custhelp@bissell. ca or at the phone number below will issue you a Return Authorization Number and a pre-paid mailing label to return the unit to BISSELL for warranty repair. The machine should be returned with a photocopy of your proof of purchase. (your dated sales receipt is your warranty ­ do not send original. ) If you need information about repairs or replacement parts, or if you have questions about your warranty, contact BISSELL Consumer Services. Website or E-mail: www. bissell. ca Use the "Customer Services" tab. [. . . ]