User manual BISSELL 92L3P

[. . . ] PowerClean BAGLESS USER'S GUIDE 92L3 SERIES 3 ® VACUUM Safety Instructions Product View Assembly Operations Maintenance and Care Troubleshooting Consumer Services Replacement Parts Additional Accessories Warranty 4 5-6 6-10 11-16 16-17 18 18 19 20 ug110-4054_92L3_608. indd 1 8/8/08 2:36:26 PM Thanks for buying a BISSELL Vacuum We're glad you purchased a BISSELL vacuum. Everything we know about floor care went into the design and construction of this complete, high-tech home cleaning system. Your BISSELL vacuum is well made, and we back it with a limited one year warranty. We also stand behind it with a knowledgeable, dedicated Consumer Services department, so, should you ever have a problem, you'll receive fast, considerate assistance. [. . . ] Do not place vacuum cleaner close enough to objects to pull them into rotating brush. www. bissell. com 800. 237. 7691 CAUTION: 9 ug110-4054_92L3_608. indd 9 8/8/08 2:36:35 PM Operations Power cord usage 1. To use your vacuum, remove the cord and plug it into an electrical outlet. For your convenience, there is a quick release cord wrap for easy cord removal. There is also a cord clip that is part of the upper cord wrap where you can attach the cord when vacuuming. Unplug power cord by grasping the polarized plug (NOT the cord) and disconnect from outlet. Be sure to first return the quick release cord wrap back to its original position before wrapping the cord. 4. 5. 10 www. bissell. com 800. 237. 7691 ug110-4054_92L3_608. indd 10 8/8/08 2:36:37 PM Maintenance and care To maximize your cleaning performance and extend the life of your vacuum, it is very important that you empty your dirt container and check and clean your filters frequently. Empty the dirt container when the dirt reaches the "Full" line on the container, or more frequently to prevent overfills. For best performance, empty after each use. WARNING:electric To reduce the risk of shock, turn power switch OFF and disconnect polarized plug from electrical outlet before performing maintenance or troubleshooting checks. 2. 3. Check the pre-motor filter and post-motor HEPA media filter at least once a month, clean or replace as needed. Replace the post-motor HEPA media filter every three to six months. NOTE: More frequent filter cleaning may be necessary if you are vacuuming new carpet, fine dust, or have allergy concerns. Unplug the vacuum from electrical outlet. WARNING:injury To reduce the risk of from moving parts, turn vacuum cleaner off and disconnect power plug from electrical outlet. 3. 1 2. 5. Place handle in low position and turn vacuum cleaner over so bottom side is facing up. 2 4 3 Lift tab 1 and release the three latches in order 2-4 marked. Clean strings, hair and other debris from rotating floor brush, paying particular attention to brush ends. Clean strings, hair and other debris from motor pulley and drive belt areas. 8. Air Passageway 800. 237. 7691 12 www. bissell. com ug110-4054_92L3_608. indd 12 8/8/08 2:36:39 PM Maintenance and care Replace drive belt 1. With rotating floor brush removed from vacuum cleaner (Steps 1-4 of check rotating floor brush and drive belt), grasp old drive belt and remove from motor pulley. Motor Pulley Place new drive belt over motor pulley and loop other end over rotating floor brush in the space between the bristles. NOTE: It is important that you use only genuine BISSELL replacement belts. Generic belts may not meet the exact specifications required to keep your vacuum operating at its peak performance. The use of unbranded belts could lead to early failure of the vacuum and could void your warranty. 3. 3. 4. Pull the rotating floor brush firmly into position, stretching the drive belt, and place ends of rotating floor brush down into the slots on sides as shown. Alignment of brush ends in slots may be necessary to fully insert the brush. Turn rotating floor brush by hand several times in the direction of motor pulley. [. . . ] Incorrect height adjustment Hose not attached to suction opening Twist 'n Snap hose not securely attached Crack or hole in hose Broken or worn drive belt Rotating floor brush bristles worn Rotating floor brush jammed Clog in vacuum Dirt container full Remedies 1. TurboBrush is clogged or debris is wrapped around the brush roll Vacuum cleaner is difficult to push Possible causes 1. Adjust powerfoot to correct height setting Visible dirt escaping from cleaner Possible causes 1. Pull out and re-insert dirt container correctly Other maintenance or service not included in the manual should be performed by an authorized service representative. Thank you for selecting a BISSELL product. Please do not return this product to the store. For any questions or concerns, BISSELL is happy to be of service. [. . . ]