User manual BISSELL 80Q2

[. . . ] Do not pick up flammable or combustible materials (lighter fluid, petrol, kerosene, etc. ) or use in the presence of explosive liquids or vapour. Do not use appliance in an enclosed space filled with vapours given off by oil base paint, paint thinner, some moth proofing substances, flammable dust, or other explosive or toxic vapours. Not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Young children should be supervised to ensure that they do not play with the appliance. replaced by the manufacturer or its service agent in order to avoid a hazard. Do not pick up toxic material (chlorine bleach, ammonia, drain cleaner, petrol, etc. ). [. . . ] For full suction power, close the air flow regulator by sliding the regulator forward to the closed position. Variable Suction Control Tip: Use the variable suction power control and the air flow regulator to reduce air flow as needed when using the tools. CAUTION: Before using your vacuum, make sure that the dirt container and all filters (pre-motor and post-motor) are in place. Do not operate your vacuum without the dirt container and filters. www. bissell. ca 1-800-263-2535 7 Operations Special tools Your BISSELL CleanView Multi cyclonic is not only a powerful carpet and rug vacuum cleaner, it's also a versatile bare floor and above floor vacuum cleaner when you select one of the special tools. To vacuum carpets and rugs, push the brush switch to the carpet position . To vacuum bare floors, push the brush switch to the bare floor position . Upholstery tool: Use the upholstery tool to clean curtains, draperies, cushions and fabrics. Dusting brush: Use the dusting brush to dust furniture, blinds, books, lamps, shelves and baseboards. Brush Up 1. 2. Brush Down 8 www. bissell. ca 1-800-263-2535 Maintenance and care Emptying the dirt container Empty the dirt container as soon as the dirt reached the "FULL" lines on the sides of the dirt container. Press the dirt container release button located on the back of the carry handle and lift up to remove. Method #1 ­ Hold the dirt container over a trash can and push the emptying button located on the back bottom of the dirt container to open the bottom. Close the bottom after the dirt empties and make sure it clicks back into the locked position. Method #2 ­ Place a plastic bag over the bottom of the dirt container. Push the emptying button, located on the back bottom of the dirt container, through the plastic to open the bottom. Close the bottom and make Emptying sure it clicks back into the locked Button position. WARNING: To reduce the risk of electric shock, turn power switch OFF and disconnect plug from electrical outlet before performing maintenance or troubleshooting checks. Dirt Container Release Button www. bissell. ca 1-800-263-2535 9 Maintenance and care Cleaning the inner cyclone & screen Filters protect the motor from dirt and dust particles. Use only BISSELL replacement filters in your CleanView Multi Cyclonic 1. Remove the top portion of the dirt container by grasping the carry handle and turning counter clockwise and pulling up and out of the dirt container. Remove the inner cyclone by grasping the bottom of the cyclone and turning counter clockwise to unlock. To reassemble, hold the carry handle and place the screen back onto the top portion of the dirt container. Be sure to align the notch on the top with the insert on the flat edge of the screen. Then place the inner cyclone back into the screen by aligning the notches at the top of the inner cyclone with the inserts inside the screen and turning clockwise to lock into place. Place the top portion back onto the dirt container by grasping the carry handle and turning clockwise to lock into place. Be sure that the dirt container release button is aligned with the emptying button when locked into place. 3. 4. 5. 10 www. bissell. ca 1-800-263-2535 Maintenance and care Cleaning the pre-motor filter The pre-motor filter protects the motor from dirt and dust particles. Use only BISSELL replacement filters in your CleanView Multi Cyclonic. [. . . ] If there are no authorized BISSELL Service Centres in your area, a BISSELL Representative at canada. custhelp@bissell. ca or at the phone number below will issue you a Return Authorization Number and a pre-paid mailing label to return the unit to BISSELL for warranty repair. The machine should be returned with a photocopy of your proof of purchase. (Your dated sales receipt is your warranty ­ do not send original. ) If you need information about repairs or replacement parts, or if you have questions about your warranty, contact BISSELL Consumer Services. Website: www. bissell. ca E-mail: canada. custhelp@bissell. ca Or Call: BISSELL Consumer Services 1-800-263-2535 Monday ­ Friday 8 a. m. PO Box 3606 Grand Rapids MI 49501 ATTN: Consumer Services BISSELL CANADA CORPORATION IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. [. . . ]