User manual BIOSTAR P4M890-M7 SE

[. . . ] P4M890-M7 SE Setup Manual FCC Information and Copyright This equipment has been tes ted and found to comply with the limits of a Class B digital devic e, purs uant to Part 15 of the FCC Rules . T hese limits are designed to provide reasonable protec tion against harmful interference in a residential installation. T his equipment generates , uses and can radiate radio frequency energy and, if not ins talled and used in accordance with the instructions , may cause harmful interference to radio communications . There is no guarantee that interference will not occur in a particular ins tallation. The vendor makes no representations or warranties with respec t to the contents here and s pecially disclaims any implied warranties of merchantability or fitness for any purpose. [. . . ] The Choices: 3 (default), 1. USB De vice Setting Press Enter to configure the USB Device. 25 P4M890-M7 SE USB 1. 0/2. 0 Controller These options allow you to enable or disable the USB 1. 0/2. 0 controller function. The Choices: Enabled (default), Disabled. USB Operation Mode This option let you select the operation mode of USB function. The Choices: High Speed (default), Full/Low Speed. USB Keyboard/Mouse/Storage Function These options allow you to enable or disable the USB keyboard/mouse/storage devices. The Choices: Enabled (default), Disabled. USB Mass Storage Dev ice Boot Setting These options allow you to choose the boot up type of the USB mass storage devices. . The Choices: Auto mode (default), FDD mode, HDD mode. 26 P4M890-M7 SE 6 Power Management Setup The Power Management Setup Menu allows you to configure your system to utilize energy conservation and power up/power down features. Power Management Setup ACPI Function This item displays the status of the Advanced Configuration and Power Management (ACPI). The Choices: Enabled (default), Disabled. 27 P4M890-M7 SE Power Management This category allows you to select the power saving method and is directly related to the following modes: 1. There are three options of Power Management, three of which have fixed mode settings Min. Power Saving Maximum power management only available for sl CPU's. When you choose user define, you can adjust each of the item from 1 min. to 15 min. HDD Power Down When enabled, the hard-disk drives will power down after a set time of system inactivity. The Choices: Disabled (default), 1 Min, 2 Min, 3 Min, 4 Min, 5 Min, 6 Min, 7 Min, 8 Min, 9 Min, 10 Min, 11 Min, 12 Min, 13 Min, 14 Min, 15Min. Suspend Mode The item allows you to adjust the system idle time before suspend. The Choices: Disabled (default), 1 Min, 2 Min, 4 Min, 6 Min, 8 Min, 10 Min, 20 Min, 30 Min, 40 Min, 1 Hour. Video Off Option This field determines when to activate the video off feature for monitor power management. The Choices: SuspendOff (default), Always on. 28 P4M890-M7 SE Video Off Method This option determines the manner when the monitor goes blank. V/H SYNC+Blank (default) This selection will cause the system to turn off the vertical and horizontal synchronization ports and write blanks to the video buffer. DPMS Initial display power management signaling. Modem Use IRQ This determines the IRQ, which can be applied in MODEM use. The Choices: 3 (default), 4, 5, 7, 9, 10, 11, NA. Soft-Off by PWRBTN This item determines the behavior of system power button. will require you to press and hold the power button for 4 seconds to cut off the system power. The Choices: Delay 4 Sec, Instant-Off (default). Ac Loss Auto Restart This setting specifies how your system should behave aft er a power fail or interrupts occurs. Former-Sts will restore the system to the status before power failure or interrupt occurs. The Choices: Off (default), On, Former-Sts. HPET Support This option allows you to disabled or enables the High Precision Event Timer. The Choices: Enabled (default), Disabled. HPET Mode This option allows you to select the modes of the High Precision Event Timer. [. . . ] The Choices: Min=0, Max=100; key in a DEC number. Start PWM Value (%) When CPU temperature arrives to the set value, the CPU fan will work under Smart Fan Function mode. The Choices: Min=0, Max=100; key in a DEC number. Slope PWM Level (%/) Increasing the value of slope PWM will raise the speed of CPU fan. The Choices: 3. 1%/ Medium(default), 0. 0%/, 0. 8%/, 1. 6%/, 6. 3%/ High, 12. 5%/, 25. 0%/, 50. 0%/. CPU Vcore, NB Vcore, +3. 3V, +5. 0V, +12V, DRAM Voltage, VTT Voltage, Voltage Battery Detect the system's voltage status automatically. Current CPU Temp This field displays the current temperature of CPU. Current CPU FAN Speed This field displays the current speed of CPU fan. Current SYS FAN Speed This field displays the current speed SYSTEM fan. Show H/W Monitor in POST If you computer contains a monitoring system, it will show PC health status during POST stage. The Choices: Enabled (default), Disabled. 36 P4M890-M7 SE 9 Performance Booster Zone Figure 9: Performance Booster Zone DRAM Clock/Drive Control This item controls the DRAM Clock. [. . . ]