User manual BIOSTAR GF7100P-M7 BIOS SETUP

[. . . ] GF7100P-M7 BIOS Setup BIOS Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1 Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Standard CMOS Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3 Advanced BIOS Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The Choices: Enabled (default), Disabled. MPS Version Control For OS The BIOS supports version 1. 1 and 1. 4 of the Intel multiprocessor specification. However, any programs that attempts to write to this memory block will cause conflicts and result in system errors. The Choices: Disabled (default), Enabled. 19 GF7100P-M7 5 Integrated Peripherals Figure 5. Integrated Peripherals IDE Function Setup Highlight the "Press Enter" label next to the "IDE Function Setup" label and press enter key will take you a submenu with the following options: 20 GF7100P-M7 On-chip IDE Channel 0 The motherboard chipset contains a PCI IDE interface with support for two IDE channels. Select "Enabled" to activate the first and/or second IDE interface. Select "Disabled" to deactivate an interface if you are going to install a primary and/or secondary add-in IDE interface. The Choices: Enabled (default), Disabled. Primary Master/Slave PIO The IDE PIO (Programmed Input / Output) fields let you set a PIO mode (0-4) for each of the IDE devices that the onboard IDE interface supports. In Auto mode, the system automatically determines the best mode for each device. The Choices: Auto (default), Mode0, Mode1, Mode2, Mode3, Mode4. Primary Master/Slave UDMA Ultra DMA function can be implemented if it is supported by the IDE hard drives in your system. As well, your operating environment requires a DMA driver (Windows 95 or OSR2may need a third party IDE bus master driver). If your hard drive and your system software both support Ultra DMA, select Auto to enable BIOS support. The Choices: Auto (default), Disabled. IDE DMA Transfer Access This item allows you to enable or disable the IDE DMA transfer access. The Choices: Enabled (default), Disabled. Serial-AT A Controller This item allows you to enable or disable the Serial ATA function. The Choices: Enabled (default), Disabled. IDE Prefetch Mode The "onboard" IDE drive interfaces supports IDE prefetch function for faster drive access. If the interface on your drive does not support prefetching, or if you install a primary and/or secondary add-in IDE interface, set this option to "Disabled". The Choices: Enabled (default), Disabled. 21 GF7100P-M7 MCP Storage Config SATA Operation Mode This option allows you to choose SATA function. The Choices: IDE (default), RAID, AHCI, Linux AHCI. SATA 1/2/3/4 RAID This option allows you to enable or disable SATA Primary/Secondary RAID. The Choices: Disabled (default), Enabled. Onboard PCIE LAN This option allows you to control the onboard LAN. The Choices: Enabled (default), Disabled. Onboard LAN Boot ROM This item allows you to enable or disable the Onboard LAN Boot ROM. The Choices: Disabled ROM (default), Int18, Int19. . 22 GF7100P-M7 LAN ROM Protocol This option allows you to select the Lan ROM protocol. The Choices: PXE (default), RPL. OnChip USB This option should be enabled if your system has a USB installed on the system board. You may need to disable this feature if you add a higher performance controller. The Choices: V1. 1+V2. 0 (default), Disabled, V1. 1 USB Memory Type This option allows you to choose the USB memory type. The Choices: SHADOW (default), Base Memory(640K). USB Keyboard/Storage Support This item allows you to enable or disable the USB Keyboard / storage Legacy Support. Enabled Disabled (default) Enable USB Keyboard / storage Support. Disable USB Keyboard/ storage Support. USB Mouse Support This item allows you to enable or disable the USB mouse Legacy Support. Enabled Disabled (default) Enable USB mouse Support. Disable USB mouse Support. HD Audio This option allows you to control the onboard HD audio. The Choices: Auto (default), Disabled. 23 GF7100P-M7 IDE HDD Block Mode Block mode is also called block transfer, multiple commands, or multiple sectors read / write. If your IDE hard drive supports block mode (most new drives do), select Enabled for automatic detection of the optimal number of block mode (most new drives do), select Enabled for automatic detection of the optimal number of block read / write per sector where the drive can support. The Choices: Enabled (default), Disabled. POWER ON Function` This item allows you to choose the power on method. [. . . ] The Choices: Disabled (default), Enabled. Resources Controlled By By Choosing "Auto(ESCD)" (default), the system BIOS will detect the system resources and automatically assign the relative IRQ and DMA channel for each peripheral. By Choosing "Manual", the user will need to assign IRQ & DMA for add-on cards. The Choices: Auto (ESCD) (default), Manual. IRQ Resources This submenu will allow you to assign each system interrupt a type, depending on the type of device using the interrupt. When you press the "Press Enter" tag, you will be directed to a submenu that will allow you to configure the system interrupts. [. . . ]