User manual BIOSTAR G31-M7 TE

[. . . ] G31-M7 TE Setup Manual FCC Information and Copyright This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation. [. . . ] This header allows only HD audio front panel connector; AC'97 connector is not acceptable. 10 9 2 1 Pin 1 2 3 4 5 6 7 8 9 10 Assignment Mic Left in Ground Mic Right in GPIO Right line in Jack Sense Front Sense Key Left line in Jack Sense 14 G31-M7 TE JCMOS1: Clear CMOS Header By placing the jumper on pin2-3, it allows user to restore the BIOS safe setting and the CMOS data, please carefully follow the procedures to avoid damaging the motherboard. 3 1 Pin 1-2 Close: Normal Operation (Default). 3 3 1 1 Pin 2-3 Close: Clear CMOS data. Clear CMOS Procedures: 1. Power on the AC. 6. Reset your desired password or clear the CMOS data. SATA1~SATA4: Serial ATA Connectors The motherboard has a PCI to SATA Controller with 4channels SATA interface, it satisfies the SATA 2. 0 spec and with transfer rate of 3Gb/s. Pin 1 2 3 4 5 6 7 Assignment Ground TX+ TXGround RXRX+ Ground SATA4 SATA3 SATA1 SATA2 7 4 1 15 Motherboard Manual JUSBV1: Power Source Header for USB Ports Pin 1-2 Close: +5V for USB ports at JUSB2/JRJ45USB1. Pin 2-3 Close: +5V STB for USB ports at JUSB2/JRJ45USB1. 3 1 Pin 1-2 close 3 1 3 1 Pin 2-3 close JCOM2: Serial port Connector The motherboard has a Serial Port Connector for connecting RS-232 Port. 2 1 10 9 Pin 1 2 3 4 5 6 7 8 9 10 Assignment Carrier detect Received data Transmitted data Data terminal ready Signal ground Data set ready Request to send Clear to send Ring indicator Key 16 G31-M7 TE JPRNT1: Printer Port Connector This header allows you to connector printer on the PC. 2 1 25 Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 Assignment -Strobe -ALF Data 0 -Error Data 1 -Init Data 2 -Scltin Data 3 Ground Data 4 Ground Data 5 Pin 14 15 16 17 18 19 20 21 22 23 24 25 26 Assignment Ground Data 6 Ground Data 7 Ground -ACK Ground Busy Ground PE Ground SCLT Key 17 Motherboard Manual CHAPTER 4: USEFUL HELP 4. 1 DRIVER INSTALLATION NOTE After you installed your operating system, please insert the Fully Setup Driver CD into your optical drive and install the driver for better system performance. You will see the following window after you insert the CD The setup guide will auto detect your motherboard and operating system. Note: If this window didn't show up after you insert the Driver CD, please use file browser to locate and execute the file SETUP. EXE under your optical drive. A. Driver Installation To install the driver, please click on the Driver icon. The setup guide will list the compatible driver for your motherboard and operating system. Software Installation To install the software, please click on the Software icon. The setup guide will list the software available for your system, click on each software title to launch the installation program. C. Manual Aside from the paperback manual, we also provide manual in the Driver CD. Please download the latest version of Acrobat Reader software from http://www. adobe. com/products/acrobat/readstep2. html 18 G31-M7 TE 4. 2 SOFTWARE Installing Software 1. The drivers installation program would appear if the Autorun function has been enabled. Select Software Installation, and then click on the respective software title. Follow the on-screen instructions to complete the installation. Launching Software After the installation process, you will see the software icon "eHOT Line" / "BIOS Update" appears on the desktop. Double-click the icon to launch the utility. eHot-Line (Optional) eHot-Line is a convenient utility that helps you to contact with our Tech-Support system. This utility will collect the system information which is useful for analyzing the problem you may have encountered, and then send these information to our tech-support department to help you fix the problem. Before you use this utility, please set Outlook Express as your default e-mail client application program. important * representsthat you informa ti on This bl ock will show the i nformation which would be collected in the mail . must provide. Wi thout this information, you may not be able to send out the mail. *Describe conditi on of your system. area *Select yourose to or the area cl you. Provide the e-ma il address that you would like to send the copy to. *Provid e the name of the memory module manufacturer. Exi t thi s dialog. Save these in forma tion to a . txt file 19 Motherboard Manual After filling up this information, click "Send" to send the mail out. A warning dialog would appear asking for your confirmation; click "Send" to confirm or "Do Not Send" to cancel. If you want to save this information to a . txt file, click "Save As. . . " and then you will see a saving dialog appears asking you to enter file name. Enter the file name and then click "Save". Your system information will be saved to a . txt file. Open the saved . txt file, you will see your system information including motherboard/BIOS/CPU/video/ device/OS information. We will not share customer's data with any other third parties, so please feel free to provide your system information while using eHot-Line service. [. . . ] Call the drive manufacturers for compatibility with other drives. 26 G31-M7 TE This page is intentionally left blank. 27 Motherboard Manual APPENDENCIES: SPEC IN OTHER LANGUAGE GERMAN Spezifikationen LGA 775 Intel Core2Duo / Core2Quad / CPU Pentium Dual-Core / Celeron Dual-Core / Celeron 4xx Prozessoren FSB 800 / 1066 / 1333 / 1600 MHz Intel G31 Chipsatz Intel ICH7 ITE 8712F Super E/A E/A-Funktionen. Low Pin Count-Schnittstelle DDR2 DIMM-Steckplätze x 2 Lüfterdrehzahl-Controller/-Überwachung "Smart Guardian"-Funktion von ITE Dual-Kanal DDR2 Speichermodul Umgebungskontrolle, Extended Memory 64 Technology / Virtualization Technology Unterstützt Hyper-Threading / Execute Disable Bit / Enhanced Intel SpeedStep® / Intel Architecture-64 / Bietet die häufig verwendeten alten Super Hardware-Überwachung Arbeitsspeich Jeder DIMM unterstützt 256MB / 512MB / Unterstützt DDR2 800/667 er 1GB / 2GB DDR2. 256MB gemeinsam benutzter Videospeicher Ultra DMA 33 / 66 / 100 Bus Master-Modus IDE Integrierter IDE-Controller Unterstützt PIO-Modus 0~4, Datentransferrate bis zu 3. 0Gb/s SATA Integrierter Serial ATA-Controller Konform mit der SATA-Spezifikation Version 2. 0. 10 / 100 Mb/s Auto-Negotiation LAN Realtek RTL 8102EL Halb-/ Vollduplex-Funktion HD Unterstützt High-Definition Audio Audio-Unters ALC662 5. 1-Kanal-Audioausgabe tützung Steckplätze PCI-Steckplatz PCI Express x16 Steckplatz x2 x1 28 G31-M7 TE Spezifikationen Diskettenlaufwerkanschluss Druckeranschluss Anschluss Serieller Anschluss IDE-Anschluss SATA-Anschluss Fronttafelanschluss Onboard-Ans chluss Front-Audioanschluss CPU-Lüfter-Sockel System-Lüfter-Sockel "CMOS löschen"-Sockel USB-Anschluss Stromanschluss (24-polig) Stromanschluss (4-polig) PS/2-Tastatur PS/2-Maus Rückseiten-E VGA-Anschluss /A LAN-Anschluss USB-Anschluss Audioanschluss Platinengröße 179 mm (B) X 235 mm (L) Biostar behält sich das Recht vor ohne Ankündigung , OS-Unterstüt Windows 2000 / XP / VISTA zung hinzuzufügen oder zu entfernen. [. . . ]