User manual BINATONE ZEST

[. . . ] TECHNICAL DETAILS Standard Digital Enhanced Cordless Telecommunication (DECT) 1. 88 to 1. 9 GHz (bandwidth = 20 MHz) 1. 728 MHz Up to 300m outdoors; up to 50m indoors Standby: 100 hours Talking: 10 hours Battery charge time:15 hours Operating 0 C to 40 C Storage -20 C to 60 C 1 x 2. 4V 500mAH NiMH battery pack Battery P/N: VT50AAAALH2BMJZ Base Unit - SIL BD060020J Input 230VAC, 50Hz, 30mA, Output 6VDC, 200mA Charger Pod - SIL BD060020J Input 230VAC, 50Hz, 30mA, Output 6VDC, 200mA TABLE OF CONTENTS 1 IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 5. 3 5. 4 5. 5 5. 6 5. 7 VIEW A PHONEBOOK ENTRY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 EDIT A PHONEBOOK ENTRY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 DELETE A PHONEBOOK ENTRY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] During a call: Press <C> to mute the microphone and "MUTED" will display on the LCD. 4. 6 Turn off the Handset Ringer In idle, press and hold <HASH/#> to turn off the handset ringer. Note: The display will still flash the Call icon and show CALL or the Caller Display number, when there is an incoming call, even if the ringer is turned off To turn the ringer back on, press and hold <HASH/#> again. 4. 7 Turn on the Keypad Lock In idle, press and hold <STAR/*> to turn on the keypad lock. Note: You can still use <TALK ON> / <SPEAKERPHONE> to answer a call when the handset is ringing. 4. 8 Redial the last number You can redial any of the 5 last numbers called. If you have stored a name in the phonebook to go with the number, the name will be displayed instead. The most recent last number will display at the top of the redial list. Note: If the redial list entry shows a name, press <Hash/#> to view the number of this entry. Press <TALK ON> / <SPEAKERPHONE> to dial to the selected redial number. Note: If there are no numbers in the redial list, the display shows "EMPTY " . 6. Store a Redial Number into the Phonebook Follow Steps 1 and 2 in section 4. 8. 1. Press <OK> and then enter the name you want to use in the phonebook. The respective ringtone will be played when browsing the ringtone list. (Note: the selected melody will only be played if you subscribe to Caller Display and the incoming number matches the stored number. ) 7. 4. 9 Find the Handset You can locate the handset by pressing <PAGE> on the base station. All the handsets registered to the base will produce the paging tone and show "PAGING" on the display. You can stop the paging by pressing <TALKON>/ <TALK OFF> /<C> on any handset or <PAGE> on the base again. Note: If there is an incoming call during paging, the phone will ring with the incoming call instead of paging. 4. 10 Make an Internal Call (For multi-handset versions only) This feature is only applicable when there are at least two registered handsets. It allows you to make internal calls, transfer external calls from one handset to another handset and make conference calls. If the called handset is not answered within 60 seconds, the called handset will stop ringing and the calling handset will return to standby mode. [. . . ] After a reset, all your personal settings, call list entries, redial list entries, and answering machine messages will be deleted but your phonebook remains unchanged. Press <OK> and you are requested to enter the 4-digit system PIN. Press <OK> to confirm, and the phone will be reset to its default settings. 8 Problem TROUBLESHOOTING No dialling tone when pressing <TALK ON> key a. The connection cord of the base station is not plugged in. Check that the telephone cord has been plugged into the base station and the phone socket. [. . . ]